Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Newly purchased nRF51 DK connected via USB cable to a computer. Attempted to program firmware via BLE sniffer and an error occurred (image attached). Connected nRF51 DK does...
I am porting our firmware from SDK v15.3.0 to 16.0.0. I believe I have most of the changes in place as I am able to build the boot loader and get it to execute without any...
Hi
I'm trying to use Crypto but can't get started because micro-ecc isn't installed
The install instructions say:
Enter the subdirectory for the SoC and the toolchain...
I have been trying to bring up a secure boot loader for our product based on the nRF52832 SoC.
I have reviewed three SDK versions (17.0.2, 16.0.0, 15.3.0) and observe the...
Hi,
I know that the QSPI peripheral of nRF5340 allows to augment memory by interfacing an external SPI Flash memory. In addition to the internal memory, does DFU by FOTA...
I use nrf52840 dongle on windows 10 to connect to ble devices, I can connect and send msg to the ble device ,but I tried "att_res, data = self.adapter.read_req(new_conn,BLEUUID...
Hello Everyone,
I'm looking for an MCU that could be used as a master for SPI communication to supply the necessary signals (CS+, SCLK+, MOSI+) to a slave device (amplifier...
Hello,
I have migrated my codebase from v1.3.0 to v1.4.0 of the nRF SDK and have a strange issue now where the serial port is spitting out sleep debugging information in...
Hi,
The nrf52832 product spec shows all the clocks provided by HFCLK and LFCLK. But where can I find which peripheral is using which peripheral clock specifically?
For...
Hi,
I need to read some BLE characteristics presented by a commercial device nRF52-based, using my nRF52-DK, based on the nRF52832 and PCA10040. I don't have the firmware...
Hello experts,
I would like to get my mind clear on this.
I am using NRF52833 for our custom board we are using Zephyr RTOS (NCS v1.4.99) and IDE is segger embedded...
We need to accurately control the time when the Bluetooth advertising package is sent out, so that the two slavers can simultaneously send the beacon data to produce the signal...
Hi,
I am facing an issue when setting up advertising intervals (in connectable mode).
Whatever the value I enter I will always end up with an advertising interval of...
Hi,
I am currently working on the ble mesh project. I would like to know whether there is any cybersecurity related examples in SDK .
1. Can you list out some of the security...
Hi,
So there is a dataflash MX25R6435F available on nRF9160 DK.
My question is that is it available for general purpose? If yes then how can it be accessed?
Unfortunately...
