But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
which is the Example code to test the NFC_Tag future in MDBT42 V P 512K V2 module.
i was using PCA10040 nrf52 development kit in that Example code is working same code not...
I want to disable and enable UART at runtime. I don't use DMA and interrupt.
I read this thread. https://devzone.nordicsemi.com/f/nordic-q-a/52496/nrf9160-uart-pull-up-and...
Hi.
I need to program for a set of NRF52832 with serial number from 403898368 to 403941418.
I am trying with nrfjprog --family NRF52 --memwr 0x10001080 --val %% --verify...
I am in the process of evaluating different BLE solutions for a project. The project consists of a pair of BLE-enabled devices which need to be able to go into dual-role mode...
Hi everyone
I don't really understand what the physical cell ID is. Is it a randomly generated ID created by the nRF9160 chip or a set ID within the cell?
As far as I...
Hello,
I am facing a really annoying issue when updating my SPI settings from the old nrf_drv_ towards the newer one nrfx , in SDK15. I am following the recommendtations...
Project context: -------------------- Server BLE for home trainer diy Target (Bluetooth server) : Bluefruit nRF52 The feather Library : BluefruitBLE Client : nRF Connect ...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
1) If I enable “Just works” and without...
I have a project where one device will be both a peripheral and a central. In the central role the device will connect to a sensor. It will act based on the sensor data. In...
Hi,
I am using nRF52840 Preview DK with SDK v15.3.0 and SoftDevice API v6.1.1
I want to set a filter in the ble scan to connect only to the specified MAC address,
...
I have been searching for hours on how to get past this. Can anyone help? This is my first time on here and I am new to SES, I am just trying to re-create a blinky example...
Hello,
Is it possible to use wireshark with the UBLOX evaluation board (EVK-NINA-B302)?
I tried but couldn't make it work. As I don't have a nordic evaluation board...
HIi
I am using the pc-driver-ble_py library to build a central in order to test a peripheral. At this point, I am interested in starting a LE ping and I saw that I should...
