This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
1. It is understood that zigbee3.0 certification requires Green Power, but I did not see the definition and use of Green Power in the example. How does the nordic zigbee pass...
Hello Everyone,
I am trying to compile zigbee_light_coordinator example. I have my path included as ../../../../../../../external/nRF-IEEE-802.15.4-radio-driver/src in make...
Hello,
I have accidential removed the DFU bootloader on my PCA10059 dongel..... is there an image that I can write to the dongle to get it back into its out of the box condition...
Hi there, I have set my SAADC to have an acquisition time of 3us , however when I toggle a pin before and after calling
nrfx_saadc_sample_convert
I measure the time of...
The sample project is "nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\experimental\ble_nfc_pairing_reference"
I think "micro_ecc" is a normal build.
Please check attached...
Hi,
Using the Secure DFU from SDK 14.2 I managed to integrate the NUS peripheral example to have access to an UART pipe in parallel to the DFU when running the boot loader...
Hi,
I am interested in testing the capability of Bluetooth 5's long range.
I have two nRF52840 dongles (pca10059 v1.0.0). So far I have had one dongle using nRF Connect...
Hi
In the example Nordic UART BLE_central, I notice that when I send data over UART to the central device, it echoes the data sent and I see it as an output in the central...
Hello,
I'm having an issue about the FDS. Indeed, i want to update some structures already saved in flash so i call the following function : fds_record_update. I can see...
I am trying OTA DFU on nrf52840 over BLE using segger. Is there any example code with proper libraries? Because I'm getting an error message: ant_error.h: No such file or...
Hello All,
I am having trouble changing the 'ble_app_multiperipheral_pca1056_s140' example to work with long range. I have read a few of the blog posts and similar devzone...
Hi all,
I am working on a project where the requirement is a sensor collecting data and sending to the NRF52832 via UART. Every 40ms, the NRF52832 will receive 40 bytes...
As we would expect, sd_ble_gattc_hv_confirm returns BLE_ERROR_INVALID_CONN_HANDLE when the conn_handle argument is invalid (i.e. does not represent an active connection)....
Can anyone tell me if the ble_app_hids_keyboard example will run OK on the nRF52810?
I'm currently using the Rigado BMD-340 (nRF52840) and my project is based on the keyboard...
I’m a new user in the BLE world. I’m trying to play with a nRF52 DK and I’m facing with a problem. I tried different IDE (VScode + platformIO, Mbed studio) with the framework...
