We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi everyone, I'm trying to understand Eddystone example in NRF5 SDK. I'm successfully run example ble_app_eddystone. I also edit Eddystone URL from mobile app. I don't know...
Hello,
I want to create a small BT Mesh network to demonstrate the possibilities and advantages of BT mesh, for example switching on two lights via BT mesh, collect sensor...
I wan to network multiple avr microcontrollers with nrf240L1+. My project is 2 0r 3 seprate microcontrollers read tempreature from their sensors and send them to a base micro...
hai, i am using sdk-v-12.3.0 for nrf52832-pca10040,
I connected the SOC to PC using Daplink.Now,i want to just print "hello world " on the /dev/ttyACM0.could any one please...
I am currently working with a custom board that captures an ECG using an AD8233 chip from analog devices. Attached to the board are gold plated pads that act as electrodes...
Hi
Does nrf52840 PD Kit support development of ble 4.2 standard applications? If yes, how can this be achieved.
NB: I have 3 nrf52840 PDKs and wanted to use them for throughput...
Nordic Team,
We are using Bluefruit LE Sniffer - Bluetooth Low Energy (BLE 4.0) - nRF51822 - v3.0 to sniff packets from BLE 4.0 device - but we are finding it hard to connect...
Hello ,
i use blinky example from C:\Keil_v5\ARM\Device\Nordic\nrf51822\Board\pca10001 folder. I want to flash the led with periods (period of 30 ms turn on 10 ms off) ...
Hi,
I'm using 52810 basing on ble_app_uart example. We use a IO to start or stop advertising. Start advertising w hen the IO level is low while stop advertising w hen the...
I use SMK BTS-04 using nrf 52832. After doing "Flash Tab -> Erase" of Keil's development environment, it became impossible to connect at all. I tried using nRF 5x Command...
I use SMK BTS-04 using nrf 52832. After doing "Flash Tab -> Erase" of Keil's development environment, it became impossible to connect at all. I tried using nRF 5x Command...
I am considering using two nRF52832 or nRF51822 's for a project which requires two way BLE communication. Pressing a button on one end should cause an event on the other...
Hello, I have an adafruit bluefruit feather m0 which has nRF51822 on it, I was able to establish a connection and send data until yesterday. When I try to find my adafruit...
