This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi all,
I am using nRF52832 SoC and nRF5 SDK for Mesh v1.0.1. I know until now there is only support for relay feature in the Mesh SDK. I want to implement low power feature...
Hello,
I was trying to connect my boards to nRF Cloud to evaluate it. Setting up Gateway on the phone and on the web at nrfcloud.com was rather easy (just following getting...
I use the SDK9.0，When a bluetooth device and android APP to connect, disconnect the bluetooth device power, why wait for 20 seconds, the APP to detect device has been disconnected...
Hello Everyone,
I want to know that i purchased NRF51 DK ..which includes PCA10040 IC.i'm using MDK ARM KEIL5 . now if i'm going to develop one BLE product so i don't know...
Good morning.
I have two nrf-51 boards and a mobile device, the SDK that I´m using is the v.12.2.0. I need that the three devices are connected at the same time and its...
Hi all,
My configuration:
nrf52832
Softdevice S132 V4.0.2
Nordic SDK 13.0
I'm using th e secure bootloader example located at \examples\dfu\bootloader_secure_ble...
The nrfgprgret register is used from the application(custom) to trigger the system into dfu mode. The nrf 52 enters dfu mode and a zip file containing bootloder.bin/.dat and...
hello, I check the standard example nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_uart\pca10040\s132\arm5_no_packs device nrf52DK PCA10040 V1.1.1 ARM Compiler :...
I am currently considering purchasing the UBLOX NINA-B1 module. This uses the Nordic nRF52832.
The very 1st thing I wish to do is to be able to send and receive information...
Hi Nordic,
I have managed to make a board which has both the nRF52 and PN532 modules on the same board (picture) , connecting it through I2C as shown on the example here...
The Event Generator Unit peripheral is new in nrf52. There is a basic description in the current manual of nrf52, but not much can be inferred as to how to use it. Could an...
Hello All Supporters,
I'm developing one NRF51822 based product.so sometimes will need to update application codes as new features arrives.so if my user update(replace)application...
Hi there,
I'm testing the "saadc" example : <InstallFolder>\examples\peripheral\saadc
I haven't changed the code.
To do this, I use the nRF52840 with SDK 14.2 and s140...
Hello,
I am probably beating a dead horse here....
I am evaluating the PCA10056/nrf52840 preview DK and using the Keil/uVison 5.24.2 for that purpose.
I have found some...
How to have control(play/pause & previous/next) over the Google Play Music app via a BLE link. I know I need HID over GATT but I downloaded the official doc and I cannot understand...
