This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi all,
I cannot find the exact connector to use for the P19 Debug out header on the pca10028 board.
The one I have has the plastic around too big so it doesn't fit.
...
Hi,
I'm working on a simple ADC application where I sample using analog channel 1 and then read the value through the debugger. However my results are nonsense. I have...
I'm using s120_nrf51_ble_driver on PC.
To connect the BLE dongle, we need to COM port number to be known (parameter of sd_rpc_serial_port_name_set). Is there really no...
I am working on a project on wireless interface between phone and SIM card. I want to use chip nRF51822-CEAA to run SIM card simulation at phone side (include wireless communication...
in nRF51822 product specification a maximum absolute rating of 3.9 Volt is reported, while in electrical specification the maximum voltage is 3.6 Volt.
The question is :...
Hi,
I have tried with the nrfjprog tool and I get the following error:
Command:
nrfjprog.exe --eraseall --programs s110_nrf51822_7.1.0_softdevice.hex --program HILO_P_01...
Am trying to setup a module where I need to send the Serial port ( say from printer/peripheral COM)
to a BLE Peripheral/Central Module. Not sure which SOC or combination...
I have a board built which is a tracking device with a GPS and GSM modem. I'm beginning field testing and have been flashing it with a Segger then disconnecting the Segger...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
I have used the nrf8002 chip before and love it but now I am trying a different application that requires a bit more smarts. I am trying to design a system that can have an...
I have an nRF51822 board that is running fine for a while. At some point, it runs into an error and calls ble_debug_assert_handler() and goes into an infinite loop. At that...
Hi all,
I am new to nRF51822,now I want to used a simple ble application to send a data,and nRF51822 ble device read this data to control RC servo motor ,for example app...
We are using S130 v0.9 stack,
and when BLE device A is connected as peripheral of iphone
and central of BLE device B at the same time
iPhone --> A ---> B
Device...
Hello,
I am working with the nRF DK trying to read a sensor over I2C. I wrote some code in Keil uVision and I finally could read the sensor. The problem now is, for some...
