Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hello! I'm currently trying to scope out chips that let me do Bluetooth Classic + BLE via a UART HCI link. I came this module and noticed that it uses the NRF5340.
NORDIC...
Hello everyone,
I'm currently working on a project wherewe use the ANNAB402 and Zephyr as out RTOS. We are developing using VSCode on a Linux VM. With a new board from us...
Hi ,
I am using nrf52840 as a peripheral HID Remote control with multi-connections, and it is able to connect with all devices like phones, computers, smart televisions...
The out-of-box configuration of Thingy 52 has a 89dB, 8 ohm, 0.7W speaker.
Can I replace that with a much louder speaker such as 4W or 5W one 4 ohm or 8 ohm?
44
I am programming with the nRF52840DKs. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am currently working on integrating...
Hi,
We're currently facing an issue with Bluetooth Low Energy (BLE) range on our custom board using the NRF5340 with SDK version 2.6.1. During testing, we observed a significant...
We are migrating the firmware of our devices from Nordic's Mesh SDK 5.0.0 to Zephyr 3.5.0, starting with the provisioner device. The SOC we use is the nrf52840 and we use...
Hi, do i need to place external hardware (antenna ?) in order to be able to read the NFC info of the board?
According to the peripheral_hids_keyboad sample:
"When the...
Is it possible to enable and disable the ADC peripheral of nRF52840 to save power in nRF connect SDK? In our application, we use ADC to get battery voltage samples after every...
Hello,
I have the task to persistently store some (2) configuration values in a Zephyr application (Nordic Version). The final version contains some external flash memory...
We have a product with the nRF5340, which are connected in mesh networks of around 20 devices to a border router via OpenThread. We are on the latest SDK version (v.2.5.0...
Hi, I'm build an applicaiton using app_timer Mode: APP_TIMER_MODE_REPEATED Interval: 5 minutes Flow: - after 5 minutes I will restart the timer (stop and create a new one...
Hello
I'm evaluating cURL with nrf9160DK,zephyrOS.
Finally, it goes well with cURL - http - however, it cant do with TLS - https -
Could you let me know how to implement...
I've been investigating the "TF-M secure peripheral partition" sample project ( nRF5340DK, NCS v2.5.0, nrf/samples/tfm/tfm_secure_peripheral ) and testing if it would be possible...
