Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I am evaluating the output power of a testboard that uses the nRF52840-QFAA.
The matching network closely resembles the recommended network in the datasheet (shown in figure...
Hi!
I am using MCUBoot and the DFU library to perform a custom firmware update (which is working as expected).
I have a question about the "swap_type" value, which is...
Hi Nordic team,
I’m seeing a repeatable configure hang with NCS v3.3.0 sysbuild on macOS. The visible build output stops after:
After inspecting the process tree, CMake...
Hi Team,
I need to use this external clock for my deep sleep use case so let me know the step forward for the same.
I am using custom board with nRF54L15 and also LXFO...
HI all,
The main program suddenly encountered assert （nrfx_grtc.c line 278）while running, which happened by chance. The following are the relevant logs
note:nrf54l15...
Hi, all!
I'm currently facing an issue with upgrading the nRF52840 firmware on a Thingy91 and would greatly appreciate your guidance. I'm following the official instructions...
Hi everyone, I recently encountered an issue while developing with the nRF54LM20A. When acting as a USB High-Speed (HS) HID mouse device, Endpoint 0 fails to respond with...
Hi,
I started from your
Bluetooth Mesh NLC: Lightness Controller/Energy Monitor sample
and I tried to insert a Light CTL Server model in the project.
After a lot of...
Hi,
BLE throughput differs between NCS v2.6.0 and v2.9.2. v2.9.2 appears to have fewer MoreData packets. (Both have CONFIG_BT_CTLR_SDC_MAX_CONN_EVENT_LEN_DEFAULT set to...
Hi,
I am using the Nordic UART Service (NUS) on an nRF52840 with NCS. Without pairing enabled, NUS works perfectly with the nRF Toolbox UART service — both sending and receiving...
In the nRF Connect SDK v3.3.0 release notes, I noticed that the QoS Channel Survey feature has transitioned from experimental to supported (i.e., production-ready).
From...
Hello Team,
I am working with Thingy91x and I was checking whether is pwm led or pwm gpio can be configured for nRF5340 of Thingy 91x. If possible will you please let me...
I'm studying with PCA10059, Keil through SWD.
Trying to customise BLE_PERIPHERAL_BLINKY.
I have changed the ble_lbs.c/ble_lbs.h,including file name / service name and...
Hello Nordic Support,
I have a question related to the bug fix in nRF Connect SDK version 2.7.0, which is the following:
I would like to understand some details on what...
