I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
Hello. I'm trying to improve the permit join-handling in our project. Right now we're simply hammering the zBoss stack with bdb_start_top_level_commissioning( ZB_BDB_NETWORK_STEERING...
The samples "nrfx_gppi/fork" and "nrfx_gppi/one_to_one" are both broken and fail to compile. I have confirmed this for NCS 2.8.0 and 2.9.1 on Linux, and 2.8.0 on Windows....
Dear nordic team,
even if enabled for mcuboot via CONFIG_WATCHDOG / CONFIG_BOOT_WATCHDOG_FEED, our device performs a reset when swapping the image. More precisely: when...
Hello,
As I understand, the nRF54L15 have pins dedicated for clock functionality.
They are marked red in figure 165 ( page 796) of the preliminary datasheet, rev. 0.8...
When I build my first blinky sample, I met a error and correct it with ( https://devzone.nordicsemi.com/f/nordic-q-a/120279/update-to-ncs2-9-1-compilation-error/529668) ....
Hello,
We use NCS2.9.0 and NRF54L15-DK do the matter development, and we use template demo, just enable CONFIG_CHIP_DFU_OVER_BT_SMP in root prj.conf, then we do the ota...
Hi,
I am currently evaluating the new nRF54L15 DK development kit.
I installed VS Code v1.96.4 with nRF Connect for VS Code Extension Pack v 2024.9.5 . I am currently...
We urgently need to add support for Band 40 (B40) to our product. Our use case is very specific, and as far as we understand, the NRF91 currently does not support B40. We...
Hello,
I'm trying the Thingy 91X but I'm having a few issue with the demo application that connects to hello.nrfcloud.com:
After flashing it with the Quick Start from...
Hello,
I have a custom nRF52820 board powered by a coin cell, and I want to measure its power consumption using the Nordic Power Profiler Kit 2 (PPK2).
Could you please...
I met some problems when add build configuration to my first application. I used the blinky sample template. And the device a nRF5340 DK. My PC can detect my devices. But...
Hello everyone,
I'm working on a project based on the nRF52840, and I'm using nRF Connect SDK 2.9.0. The project uses MCUboot, but the firmware image is signed externally...
Hello, I am using NCS 2.9.0, an nRF5340, custom board files (see attached), and no external flash and I would like to use simultaneous DFU over BLE. I believe this should...
