i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
I am trying to measure the frequency of the square wave on the ARDUINO_6_PIN on the NRF52840 Dev Kit. It seems like it works well until the square wave goes above 2MHz. Is...
Hi,
I see that in the latest SDK 17.1.0 there seems to be no example for regular UART but only for LPUART.
That made me wonder if there is any advantage in any scenario...
I have an external flash
S25FL132K
I am able to read , write and erase the flash with nrfx_qspi_cinstr_xfer function for 9 bytes. But I want to write more than 9 bytes...
Hi all, I am working on an electronic lock using the nRF52840. Currently it works using Bluetooth Low Energy and the lock opens when a digital key has been sent. (it has measures...
Hello sir,
I am sending the data of 252 bytes through send_notification() at each interval of time but when i send through send_notification() then following error occurs...
Hi,
I am compiling micropython port for Thingy:52. I am following instructions here https://github.com/micropython/micropython/blob/master/ports/nrf/README.md
I see that...
Hi,
I have created an HSL model and it's working fine. Now, I am using a light that has both CCT and RGB control. So, I have both HSL and CTL model existing in the same...
Board ：52840dk_52840
SDK： NCS1.7.1
IDE ：Visual Studio Code
I remap my bootloader partition in my application .overlay file
as
& boot_partition {
reg = < 0x000000000...
Hi,
When i changed NRF_LOG_ENABLED from 0 to 1 in file sdk_config.h returns the following error
1> Linking tdoa_tag.elf 1> E:/gcc/arm-none-eabi/bin/ld: Output/Debug/Obj...
Hello, did you test the working of 100 pairs (Transmitter and Receiver) nrf52840 BLE modules together indoors? If you did, how much data is lost while working together? Can...
Hi everyone,
I use the radio example as my basis. I call the read_packet() function from receiver example. And there is no incoming data, it stucks there. How can i set...
Hey,
I have an app based on the UART central example. I successfully connect and bond to an android and am able to send data via uart over BLE.
I want to send data also...
Hi
I am converting libraries MAX30105 Arduino to nRF52840, but I have a problem,
"MAX30105 parrticleSensor;" what is it?, how can I to convert this? is it a variable?...
Hello , I am trying to build the bootloader source code provided by Adafruit for its nRF52 core. The project is based in Segger Embedded Studio.
Adafruit's nRF52 core bootloader...
Hi,
1. I removed RTT related codes in the project.
2. Will uncontrollable factors be introduced?
3. Is there any potential risk when the code runs?
Thank you for all...
