Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hello dear,
I am installing Embedded Studio on OSX (Catalina), and I following the nRF Connect step... all goes fine, but when I try to use "Open nRF Connect SDK Project...
I'm trying to see debugging info with nrf51 dongle.
As far as I can tell I just need to use:
#define NRF_LOG_MODULE_NAME "APP"
#include "nrf_log.h"
#include "nrf_log_ctrl...
On a nRF5340 DK the sample ncs/zephyr/samples/subsys/usb/cdc_acm runs fine. However, if I add "CONFIG_NO_OPTIMIZATIONS=y" to prj.conf I get faults (see below). Any ideas why...
Hi,
I am preparing Windows desktop application which will use nrfutil for DFU of the products (containing secure dfu bootloader). I tested nrfutil v6.1.0, v6.0.1 and even...
Hii guys,
I am trying to establish communication between two nrf52 module.
My application is as following
1. I need a central device which can work as master and remains...
Hello, I am stuck initalising both TWIM and UARTE. I am focusing on the TWI Scanner example but using TWIM instead of TWI. No matter what I do I cannot get past the initalisation...
Hi,
How can I increase TX Power in nRF Connect SDK ?
I have already followed the hci_pwr_ctrl example, but I got the error "Read Tx power err: -5 reason 0x00" in get_tx_power...
We use nrf connect sdk under linux.
I need to control tx power to be able to adjust working range.
I take example from zephyr/samples/bluetooth/hci_pwr_ctrl
Add segger_rtt...
Hello,
I recently cloned NCS v1.5.0-rc1 using west init -m https://github.com/nrfconnect/sdk-nrf.git followed by git checkout v1.5.0-rc1 and then west update in the nrf...
Hello,
I'm a beginner and I'm a bit lost. It's rather complex to understand everything there is to know. So I ask a lot of questions, sorry.
I was advised to use the lib...
Hello,
We are not finding RFX2401C on the market for sale and we are looking for a PA for the NRF24L01+.
We found the alternative RFX2411, is it safe to assume we can...
Dear community
I'm developing BLE secure firmware on an event-driven proprietary RTOS.
According to the documentation of nrf_ble_lesc_request_handler() , it is required...
Is the BLE connectivity offered by the nRF52840 (upon which the Arduino Nano 33 BLE is based, I think) DIRECTIONAL? Should the board be oriented in any particular way to maximize...
I would like to use the Shield Debug (P20) on the nRF52840DK as part of a Device Under Test platform for production devices. I also want to be able to transmit/receive data...
