But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Goodmorning,
what is the maxium current output for SPI pins on the nRF24LU1? The datasheet say "IVDD External load current" of 2mA, is this refered to the internal regulator...
In the documentation of the nRF SDK for Mesh v4.1.0 is written: "The following figure demonstrates how the data packets flow between mesh nodes and their layers within the...
Hello
Beacon using timeslot API
I am trying to implementing a beacon functionality using your timeslot API.
The beacon shall run in parallel to the normal SoftDevice...
Hi all,
In our application we have a piconet master (acting as GATT client) and several piconet slaves (acting as GATT servers). We have only limited time on the channel...
Hello,
I've asked this question already at StackOverflow, and while I try Wireshark I wanted to see if someone has experienced the same issue and/or can provide further...
I can scan beacons with Scanner. and can use NUS (ble_periperall\ble_app_uart ) to get connect with device.
My goal is to combine both application Have NUS Service to connect...
As most developers using Nordic's SoftDevice quickly find out, halting the processor (e.g. hitting a break point) results in a fault and requires a reboot. This makes debugging...
we want to use nRF52833 as BLE5.1 AOA/DOA locator,here are some questions about to how to use it:
How many antennas are needed for direction finding/positioning? Is 6...
Hi everyone,
I have added the Characteristic User Description in order to add a human-readable name for my characteristics. However, the name still appears in hex format...
Hi everyone,
I have created a vendor service that works fine. Now I want to create a second one. What is the most efficient approach for doing this?
For the first service...
I am following the Zigbee Device Upgrade OTA tutorial and have run into an issue flashing the server firmware using a j-link and Particle Xenon dev board.
Environment Details...
Hi all,
I seem to be having a problem with running nRF connect for desktop 3.3.1 on MacOS (10.15.3). After installing the package to the application folder, on launching...
Hi,
When configuring a GPIO as output with DRIVE set to D0S1, i.e. "Disconnect '0' standard '1'", what is the leakage current when GPIO is set to 0, i.e Disconnected?
...
Hello,
I'm porting from ST32L151 to NRF52840.
I want to use the HMAC SHA1 method, but I can't see the related function.
The nrf_crypto_hmac_init function seems to...
