Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello
I need urgent help. From days I have been stuck exploring NRF SDK 15.0 to do a simple task.
I am using an NRF DK board PCA10040. After going through peripheral drivers...
Hi,
I am working with central and peripheral uart example and facing with connection problem between two boards.After debugging at the central side i am getting error in...
Dear Sir/Madam,
We have a customer to develop a product based on nRF51422 and then they passed their product for pre-registration test.
They used DTM interface to connect...
Hello
I have nRF52832 custom board and have BME280 sensor connected to I2C/TWI
Whatever I do I get same reading (for 3 different sensors)
I'm constantly reading same...
Hello, I would like to use nRF24AP2 in a SPI bus with an accelerometer (a slave peripheral). I need that the host works as master with accelerometer. But in this way we will...
Hi,
We have designed a custom board using the nRF52811 chip which has BLE 5.0. I tried running the " ble_app_uart_pca10056e_s112 " example on the custom board and it did...
Has anyone successfully built the pc-ble-driver static library in Visual Studio as a project? In this manner one could debug applications that use the library when there are...
My code bluetooth module hangs if I use flash storage functions inside the ble_evt_handler . I am using the functions from the fstorage example in peripheral folder. I turned...
I have always understood it to be dangerous to invoke a call in a callback. It is not clear to me what the callback model is in SoftDevice so I would like to know when it...
Hi
I have searched a LOT but I can not find if Nordic can record audio with high enough fidelity to a SD card (I have seen in the SDK how to attach a SD card ).
I want...
Hi everybody,
we're testing our device with nRF52840 and full Bluetooth 5.0 by sending some packets over coded PHY and receiving them via nRF Connect for Mobile on an Android...
Hi .....
Here i want to make mesh topology between 5 boards , in that one has to act as client and other has server . i want to send the string data from client to particular...
Hi all,
I am trying to write in flash but when i use:
pg_size = NRF_FICR->CODEPAGESIZE; pg_num = NRF_FICR->CODESIZE - 1; // Use last page in flash
addr = (uint32_t ...
Hi, I've being using an arduino to collect pressure measurements from the BOSCH BMP280 pressure sensor over I2C. I want to do the same using the nRF52840 and miniturize my...
