Hi every one !
I am trying to get working a code that it was working "Ok" 2 years ago.
Currently, I cannot get communication between both breakout boards.
To simplify...
I'm trying to solve an intermittent problem when using the nRF51422 UART with CMSIS-RTOS (RTX) and MDK Networking library (V6.2) (TCP/IP stack).
My questions relate to...
Hi...
When i was working in SDK v6.1.0 i have tried nrfprog.exe to merge and program bootloader, softdevice, application and bootloader_settings file as explained in devzone...
But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
I am getting intermittent pickup of advertising packet from a peripheral known to advertise every 2 second. Basically I get ~20 sec gaps where nothing is received.
Below...
I want to use the ble in nrf51822, and I use the example in nrf51_SDK_11.0.0 and softdevice in nrf51_SDK_11.0.0 \s130nrf51201\s130_nrf51_2.0.1_softdevice.hex(thougt the example...
Hello
I am currently looking for the best method to write and read values in the flash. My values are 17 uint16_t arrays with 216 indices per array. I would like to store...
Hello All I am new to this nordic semiconductors. I need information regarding nRF52840 DK boards.
* How to connect two nrF52840 DK(transmitter to receiver) and start advertising...
Hi, I have a SIM800L GSM/GPRS module that I can successfully talk to via the UART on the nRF51.
I can tell it to dial numbers etc and that all works fine.
My problem...
Hi, I'm using app_pwm with 32.768Khz external xtal. the following is my setting in sdk_config.h.
// <0=> RC // <1=> XTAL // <2=> Synth
#ifndef CLOCK_CONFIG_LF_SRC #define...
Hi,
I used sdk 15.2.0 version, I refer to the ATT_MTU Throughput Example to modify the Nordic UART Service (NUS) Application example.
Now I have some questions:
1. How...
Hello,
I'm using nRF52832, SDK15.0.0, Softdevice S132.
What should be the code added to application in order to support BLE DFU service?
I've been here , but its for...
hello,
I want to use RSSI on nrf52832, and the project is uploaded.
the question is, I test the RSSI on channel 2468MHZ, the NRF_RADIO->RSSISAMPLE result is about -92dBm...
Hi,
I followed the instructions for Getting Started with the NRF9160, activating the iBasis SIM card, placing into the board and applying USB power.
The first issue...
Hi,
I'm trying to update the firmware on my nRF9160 development kit
I downloaded the modem firmware and DFU tool
And then tried to follow these instructions: ...
Hi,
I want to activate eDRX on mqtt_simple example and measure the current consumption. I guess based on the code, by enabling "CONFIG_LTE_EDRX_REQ" it will be activated...
Hi guys,
I know that there is no official support for C++ on NordicSemi side, but I just wonder if it would be possible to work with C++ in Segger IDE. I'm trying to integrate...
SDK version: nRF5_SDK_15.3.0
Platform: nRF52840 DK
SoftDevice: s140
--
Hi All,
I use ble_app_blinky example and Android nRF Blinky SDK to add new function.
Recently...
Hello,
I'm using NRF52840 module to make a customer device. This device send message by UART. My device is powered with a battery, for this reason I would like reduce the...