Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
(assume all resources being used)
This may also include consumption at Start-up.
i need this to calculate my power requirements for a special module being developned...
Hello!
I want to create my first BLE devices and nrf52 is a choise. Devices should work as described below and before I purchase few nrf52 DK I want to be sure that it...
hello
I am a beginer to design with wireless and I would like to know with soft can be used if i have one master with 4-6 slaves. It seam to be a S120 it right ?.
Also...
Hey all. I'm working on a really simple beacon application and I'd like to use RTC0 when the BLE stack isn't using it... is that possible? No BLE connections, just 1 advertisement...
Hi,
I'm facing a weird problem resulting from the following code:
while((!twi_tx_done) && timeout--);
The main file and the MPU9150.c which includes this command...
Hi, I try to capture ipv6 over ble packet.
So, I construct system like, nrf dk 51(with sensor) - rasp
nrf-dk 51 is equipped with coap-server source and rasp doing like a...
Hi everyone,
I have a really weird problem.
I created a makefile based on Nordic's example from the app_template and created 2 additional targets, one called "debug" and...
I have upgraded my laptop to Windows 10 and all hell break loose.
When I either connect the board or the dongle, they are stuck in a loop of connect/disconnect behavior i...
hi,
i am using ble_uart example in which i am sending 3 byte of midi data
(90 1e 45 0a .E.)
i am getting (.E.) when i converts this ascii value to hex value i get (2e...
Im trying to provide DTM functionality for certifications tests. I can't setup an UART interface, I found the below code which tries to use DTM without UART. it uses channel...
Hello,
I've read a lot about trouble people had when they used bluetooth and flashed the rom without using the propper softdevice APIs.
What is the issue with concurent...
Good morning.
I ´m working with nrf51-dk, sdk 9.0.0 and softdevice 110.
I have done a proyect without softdevice, only uart and master spi (mode 0) and works perfect...
Hi, I flashed the Proximity Application to nrd51822,with s110_nrf51822_6.0.0-5.beta.
the chip run right, and I used the NRF Master Control Panel, when I write data 0X02 to...
