Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
HI
I am using the DTM example routine of NCS 3.2.1 and am currently testing the combination of nRF54L15 DK and nRF21540 EK. After flashing the original example routine to...
I’m using an nRF54L15 evaluation board obtained from a distributor and currently testing transmission and reception of large data chunks. I built a vender model and a custom...
General flow when the issue occurs:
1. buf is allocated on prep_pool in prep_write_cb: data -> buf = net_buf_alloc ( & prep_pool, K_NO_WAIT);
2. buf is put to prep_queue...
Hi everyone,
I am currently working on a project using the nRF54L05 and SE052F (from NXP).
I found this GitHub link: https://github.com/NXPPlugNTrust/nano-package/blob...
We are using an nRF52840 running SoftDevice Controller (SDC) in a custom Host + Controller architecture:
SDC runs on nRF52840 as the Bluetooth LE Controller.
Our...
Hi, I run Matter test TC_DefaultWarnings.py but failed the test, see below the last part of the logs:
******************************************************************...
Hello! I am trying to upload 120KB of data through 2 protocols: https and mqtt+tls. Both the cases have same configurations enabled in the context of wifi, net mgmt, network...
Hello, i'm trying to flash mfw-nr+_nrf91x1_2.0.0.zip on a thingy91 x. it doesnt work via nrfutil nrfutil device program --firmwaremfw-nr+_nrf91x1_2.0.0.zip THINGY91X_13A2EC8A4FC...
The examples for the Matter Light Bulb app and others contain pm_static_...yml files with sections that look like:
I cannot find "orig_span" in the Partition Manager documentation...
I was asked by Nordic tech support to create a new ticket, because ticket number 357092 had become a long a winding thread.
I need a simple utility I can offer to an end...
I am developing a project using nRF5340 to drive some peripherals. During debugging, I found that no matter how I executed the pull-up/pull-down commands, the p1.00 and p1...
I am using qt C++ to refactor the dfu master station, currently I have a problem, that is, I want to communicate with 52840 simulated com but failed, I initialize, you see...
When I click ACTIONS/Build to build, the executable module(merged.hex) is not created. Now that zephyr/zephyr.elf has been created, the process will finish.
[Environ] nRF...
Hi,
I wanted to characterise the CS accuracy by changing the default parameters in
I get errors when I try to change rtt_type to sounding sequence. I tried both 32 and...
My customer Penguin ID has the following question about HCI USB for the nRF54LM20A. He claims this is only on the old Zephyr stack and not on the new one. Can you please comment...
