After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hai,
I am trying the fast pair - locator tag example on my nRF52833. I am using SDK version 2.7.0. The code is compiled and flash properly. In the serial terminal getting...
Hi all , I 'm using nRF Kconfig and DeviceTree extension in VSCode . When I try to activate context , dropdown menu doesn 't offer any options . Are there any additional configuration...
Hello,
I have a question about connecting the device to an LTE network. According to some tests I've carried out and some questions I've seen on devzone ( https://devzone...
Hi,
I have a question about the SMS sample ( https://docs.nordicsemi.com/bundle/ncs-2.6.1/page/nrf/samples/cellular/sms/README.html ). I can use this sample to send and...
Hello Nordic Community,
I am currently working on a project that involves transitioning from a working Arduino application to a finished IoT application targeting Garmin...
Hello everyone! I'm testing a device using nRF52832 module in quite noisy environment. I've experienced BLE disconnect and looking at RSSI value, I can see it went down to...
Hi,
I have a central, where I want to close the BLE connection and restart the device. I have a button interrupt that does this:
However, when the device reboots. I...
I ran across this issue while troubleshooting a separate issue, in which I have an nRF52810-based board with no external LFCLK oscillator that is rock-solid with nRF5 SDK...
Hi,
I'm developing on the current setup:
nRF52840
Soft Device 140 version 7.2.0
SDK 17.1.0
MDK: 8.51
Segger v4.52c
Secure bootloader (DFU)
I don't define...
Hello,
Is there any USB device stack available for bare metal development on the nrf5340 using online NRFX lib. I am trying to implement a USB CDC device class.
No issues...
I am using NCS v2.5.1 and working on a project where I need to turn off the system using a button that triggers an interrupt on a GPIO. I want this GPIO to control a load...
Hi Nordic team
Currently I am trying to send a big chunk of data close to 100 KB from my nRF52832 to nRF connect for mobile app in Android phone. I am able to send few bytes...
Objective : Develop a BLE mesh application with nRF52840 as a sensor node. The sensor captures various parameters ( Temp, dissolved Oxygen etc.) and communicates them to relay...
software:ncs 2.5.0
hardware:nrf5340 dk
hi professor,
According to the article at https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/optimizing-power-on-nrf53...
I have found that in Linux, "nrfutil toolchain-manager launch --shell" is starting a process that uses almost 20% of the CPU according to the top utility. I have found this...
