Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I have a preset stored in CMakePresets.json:
When I go to create a new build configuration with the preset, the extension creates an Extra CMake Arguments row with:
...
I am working with SDK v2.3.0 and a custom board with nRF9160
When I wanted to start my project again after some time, the build configuration had disappeared.
And creating...
Hi everyone,
We're using the "Manufacturer Specific Data" field within its advertising packets to send the firmware version to a phone application. It requires the company_indentifier...
Hi, I'm working on provisioning a Pre-Shared Key (PSK) during manufacturing for an nRF5340 device. The device needs access to the PSK at runtime to generate authentication...
Hi,
I tried to add a pairing PIN code feature for connection with a central device (based on the reference: Migrating to Peer Manager ) in the ble_app_uart example of the...
nRF54L15 would be used as thread RCP, host processor would use uart to communicate with the rcp. They would behave like a OTBR.
I also need to do device firmware update...
I have created a custom board with an NRF52840 on an Ebyte E73-2G4M08S1CX. I am trying to burn a bootloader to the chip using OpenOCD and a Raspberry PI Pico W as a debugger...
Hello, I'm developing with an nRF54L15 Revision 1 (QFAA-B00). I'm encountering a problem described in the errata: 3.4 [8] SPIM: Wrong data is transmitted on MOSI (Symptom...
Hi,
I am using the nRF52840 with nRF-SDK version 16.0.
At random intervals, I encounter the following error:
"[00:02:51.009,460] <error> app: ERROR 1813 [Unknown error...
the older nrf52-DK has a header for external and one for current measurement.... how do i achieve something similar on the nrf54L15-DK, which exposes the 3-pin P6 header?...
Hello
I'm working on a custom electronics board with an nrf54L15 (QFAA). This MCU is interfaced with an EEPROM memory (24FC16T) via an I2C bus connected on P1.03(SCL) and...
After programming the DK, it "fails to verify device" with the following log:
2025-07-08T09:42:05.940Z INFO Initialising the bundled nrfutil device 2025-07-08T09:42:05.957Z...
Hello guys!
I have a strange problem where the nrf9151dk suddenly won't power up. It was working fine - I was only working with SW, not HW.
I got a pop-up error saying...
I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
I have a service and characteristic that is Notifying data at a rate of ~160 kbps.
Both our custom app and the nRF Connect app appear to be receiving the same packet over...
