This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi,
I want to create a file and save it to device storage or my computer.
As a result, I want to save a large amount of data in a text file, compress it, and send it to...
I'm having some issues with the printing to the debug terminal. I'm using SDK16 with SES 4.5 and developing on the nrf52840 DK.
I followed the instructions in this video...
I bought a pack of Vodafone NB-IoT SIMS from Arkessa for use in London, UK as there is currently no LTE-M availability where I live.
Arkessa have provided the following...
Hi,
If I don't configure GPIO pin (for LED), the led is not lit, and it doesn't draw any current. (16uA).
But If I configured it as output, then disconnect, OR output...
Hi,
i need to Stop the softdivice in my application with --> sd_softdevice_disable ( );
This is ok, it works. But later in the applictaion i have to restart or enable...
Hi Nordic team
I have successfully programmed my PCA10056 for example light-switch and they running well. Right now I wang program my PCA10059 for a server of example light...
Hi,
I tried to use latest version of nrf sniffer v2.0.0 and i received ERROR: packet creation error as you can see in the log below.
INFO: kwargs: {'callbacks': [('*'...
Board: PCA10040 (NRF52832)
Compiler: GCC
SDK: 14.1
I'm trying to add the buttonless DFU service to my application and I've had several issues.
First, I have a...
Hello,
I want to transfer data from nRF52840DK to nRF9160DK using SPI. I want to use nRF52840DK as master which will transfer the data and nRF9160DK as slave which will...
Hello,
What happens with the LPN firmware if it currently has an IV index of 0 and loses power for an extended period of time. When it gets power, the network that it is...
Dear All,
I am using the example UART in Peripherals
I can send data easily but have problem in receiving data. When I try to receive data the UART Fifo Event handler...
I looked through the example projects provided in the nRF5 SDK for Mesh, and the only models ever used are generic on/off or generic level. Do you guys have an example which...
Hi,
Sorry for the seemingly simple question. I'm using the nRF52832 chip and I have a 4xdip switch connected to P26, P27, P09/NFC1 and P10/NFC2. I can successfully read...
Hello,
I recently updated the asset tracker on my thingy 91 with the lastet available pre build firmware (2019-11-29_d3130d77) using MCUBoot.
Since my Thingy91 is only...
I started with the mqtt_simple example.
I added:
#CONFIG_MQTT_PASSWORD="pass" #CONFIG_MQTT_USERNAME="David"
to the prj.conf file. Relaunched the project which rebuild...
