Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hello, I've developed a BLE Mesh Network using the NRF MESH 3.1.0 SDK and the nR5F SDK 15.2.0. My network has 1 client node and max 63 server nodes: I'm using the generic...
I've been developing a solution that utilizes Mesh DFU along with the Mesh Bootloader. However, I've been seeing a frequent issue where the DFU aborts prematurely due to missing...
Dear DevZone,
I'm trying to use the Seeed CAN BUS Shield V2.0 (MCP2515) with the nRF52840 DK, but the library provided is written for Arduino One.
Do you know if any already...
Hello.
I m looking for libraries wich contains functions/methods (for example how to scan, provision, adding nodes etc. ) and solution how to use them.
I found something...
I am working with nRF 52832 platform and I soldered SB12 and cut SB10 because I wanted to feed from the external power supply and with this situation I can not connect to...
I have been working with the Nrf52840, SDK15.2 and Segger Embedded Studio 4.20a using external GNU 7 2017-q4-major. The project builds without error on the original PC. I...
Hi
How to find out which BLE version is supported for a given Nordic SDK + SoftDevice.
From which version of Nordic SDK is compliant to Bluetooth 4.2 ?
Hello,
This subject is partly a conclusion and partly a question I would like confirmed.
Our scenario is that we would like to fetch flash logs over BLE, but not really...
“EBSHSN” is reset by the RESET pin when the control CPU shifts to sleep mode when the terminal device is stopped. When measuring the current consumption in this state, about...
Hi, nordic.
I've been developing a product with ws2812B.
As I know, ws2812B is needed around 5V to work well.
And I measured voltages on 52 DK board.
VDD pin has...
Hi,
I designed a customer board and defined my own board header file, which is pretty much copied from pca10056.h. One question I encountered is I somehow couldn't toggle...
Hi,
I try to develop a fix that should allow me to use the pc-ble-driver to receive scan responses (see https://devzone.nordicsemi.com/f/nordic-q-a/50082/pc-ble-driver-no...
I have one doubt that why there is elements or models in Bluetooth, it can be simple as sending messages and then translate them into useful work, in this single element and...
hello,
inorder to send a string over ble from a slave to master or master to slave what is to be done??
is there any function for us to pass the string??
I want to understand the meaning of "standard drive, low frequency" GPIO pins. The datasheet mentions to use these pins for frequencies below 10 KHz. Does this limitation...
