I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi,
We are implementing a synchronous light flashing of multiple devices, so:
1) Can we get a millisecond level (< 10ms) time synchronization by parsing the Link Layer...
Hi, all
I added a scanning module to the example 'ble_app_uart.c', so each one works well.
What I want to do is advertising and connect at the same time while connected...
What is the best practise for multichannel SAADC conversion in ultra low power devices? For example I have to measured 4 channel in interval 250ms. Below what I try:
...
Hi, Dear Nordic & all:
when I run the ble_app_hids_keyboard example in nrf52820(SDK17.0.2), I meet a question:
1、Frist I use my iphone connect ble device and pair success...
Dear Nordic:
so I want to know In nRF52 serials chips, How much HFCLK CONTROLLER ppm is the frequency offset distribution and production FT control range? Do you have any...
Dear all, now I am making a data sampling system with multi peripherals and one central. The peripherals sample data from sensor via SPI port and transmit data to the central...
Any SSD1306 example for nrf51822 ??? I found this but is for nrf52.. i try to add it for my nrf51822 but there are tons of functions with different declarations in my sdk...
I have nRF5340dk board and my question is that can I use only networking processor to run the BLE applications? If not why? As the Radio hardware is only connected to networking...
Hello , I want to read analog values from potentiometer using analog pin P0.04 (A0) on nrf5340 with zephyr ecosystem . Where can I get beginner documentation like setting...
Hi,
I'm a beginner, and currently working to implement a low-power controller using nRF52-DK and Power Profiler Kit (PPK).
I ran the following codes (system off) and expected...
I have setup a 1-1 paired central(+peripheral) <=> peripheral Central is a 52832, SDK 16.0, SD s132 v7.0.1 peripheral is a 52811, SDK 16.0, SD s112 v7.0.1 My code is based...
in this example
/root/ncs/nrf/applications/serial_lte_modem
I want to build_nrf9160dk_nrf9160 in secure mode
but compile error #ifndef CONFIG_TRUSTED_EXECUTION_NONSECURE...
Hello,
I am confused on which plateform I should use to program my nrf52832 chip.
First it is advertised to use Segger Embedded Studio that I am trying to configure...
Hi all. I am using Keil for programming a nrf51822 & SDK 12.3 I want to use the SSD1306 OLED Drivers in my project I follow these steps: 1) I copy .c and .h files form github...
Hello,
Im using a NRF52840 custom made board and im having some issue with the I2C communication. There are 3 units on the I2C line, the MCU and two sensors, the diagram...
