I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hi,
I'd like to sample PDM at 48kHz, I'm using nRF52840 DK and nRF5 SDK.
I read a post ( devzone.nordicsemi.com/.../single-pdm-microphone-at-higher-pcm-sampling-rate)...
I'm bringing up ble_app_hrs as an eclipse project using gcc.
I'm running into an error in app_util.h, line 67:
#define STATIC_ASSERT(EXPR) typedef char static_assert_failed...
Hello,
I'm using the following setup:
nRF Connect SDK v2.9.0
B0 , upgradable secure MCUBoot, and application
Statically defined partitions in the partition manager...
I am experiencing issues configuring an SPI-based SD card interface on my nRF5340DK using NCS v2.7.0. The SD card is not initializing correctly, and I am receiving repeated...
I have two nRF52833 development boards: one is connected to the nRF21540 EK as TX (using BLE peripheral_uart), and the other is used as RX (BLE central_uart). My issue is...
Hello,
I recently updated to the "new" nrfutil tool and installed the nRF Sniffer according to the instructions. I programed the firmware and ran nrfutil ble-sniffer bootstrap...
Hi.
I am looking for help with software development for my Thingy91 project.
Project is very basic and I am ready to pay based on hour rate. It is very simple and beginner...
Hi support team,
I'm working with nRF52833 DK. installed the mobile app and desktop, but I wasn't able to connect to either.
Power switch ON, SW6 on DEFAULT. J2 connected...
Hi
The Blinky Programm only starts when I give the reset Go command via jlink commander.
At Power cycle nothing happens.
If i give the SOC an external Pin reset the...
We have written a Flutter app, which uses the Flutter-nRF-Connect-Device-Manager package to perform firmware upgrades on bluetooth devices that the app bonds with.
If iOS...
Hi,
I’m looking at starting a new design that would be based on the nrf52840, however it seems that the flash readout protection is now fairly broken on this device. Are...
Both myself and a colleague had an issue in the past 48 hours where upon launch we were prompted to install a new West workspace/SDK. In my case it "tricked" me into installing...
SDK: 2.6.1 (2.9 seems to give an HCI build error , undefined reference to `__device_dts_ord_135', when enabled CONFIG_BT_LL_SW_SPLIT, CONFIG_BT_LLL_VENDOR_NORDIC ?)
SOC...
Changelog for nRF Connect SDK v2.2.0 mentions that:
nrf_dm_high_precision_calc() now handles out-of-memory errors by returning NaN .
What exactly are the memory requirements...
We want to generate 8.200 MHz as I2S MCK with an nRF5340.
This could be achieved with 12.300 MHz ACLK as source for MCK, and then dividing by 1.5 in the Master clock generator...
