This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I'm using an nRF52840 with SDK 15.3 under FreeRTOS and SES, BLE only
I'm trying to implement a master side (I've got the peripheral side running no problem). The idea is...
Hi,
We have a modified asset_tracker_v2 application. We wish to take the entire application, just the code under nrf/applications/asset_tracker_v2 (including all of our...
NCS 2.8.0, NRF52840 with accurate crystal LF CLK
I've been asked to tightly synchronize timestamps for data collected by external sensors on multiple boards. The timestamps...
seems like all packs cannot be downloaded from Keil 5. all address are invalid, include all examples.
The requested URL /nRF5_SDK/pieces/nRF_DeviceFamilyPack/NordicSemiconductor...
Issue:
The OTBR could run with RCP versions built with SDK v2.3.0 and v2.4.2 but couldn't work with fw from SDK v2.9.0. Hence, I wanted to know which of the latest SDKs...
I have been working on a project using a nrf52832 and currently have the firmware developed on nrf5sdk. I have been testing out Zephyr with this example https://docs.nordicsemi...
Hello
I'm using the NRF52840DK with a custom shield on top that interfaces to my custom board. I use it to program and debug the DUT via the DK, talk to the DUT over serial...
Hello,
I am working on an update of older FW implementation: nRF52832, SDK 14.1.0, with SoftDevice S132 and using BLE connection.
The change I need to implement is a functionality...
Dear Nordic Technical Support,
I’m currently evaluating the NFC functionality on the nRF7002-DK with the following setup:
Hardware: nRF7002-DK
SDK Version: nRF...
For power-saving we periodically enable/disable the net-core. We would like to use the WDT on the net-core
as well. Since you cannot stop the WDT, how should we handle this...
When I first set up my system I had a color code view of the RAM in my system where the colors corresponded to grouped data objects. Somewhere along the line that view has...
Hello,
I am unable to use the Segger RTT terminal built into the nRF Connect SDK for VSCode Extension pack with the nRF54L15DK.
I have configured my project with the...
Hello,
zephyr: Vanila v 4.1.0
I'm trying to run FOTA via BLE on the nRF54L15DK. I’ve configured everything as it should be, based on the sample:
When I...
Hello,
Is it possible to make the nRF Sniffer for Bluetooth LE application work on a nRF54L15?
https://www.nordicsemi.com/Products/Development-tools/nRF-Sniffer-for-Bluetooth...
Hi, I am testing the PaWR examples in the NCS and I have few doubts.
In this page , it says in section 1.3 that there are two ways for synchronization - PAST after connection...
