I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi Nordic team,
We have tried using Bluetooth peripheral HID keyboard example from nRF5 SDK and found an interesting problem.
In our setup, nRF52840DK is running the provided...
Hello all,
I have trouble reading saadc data with an amplitude of 10 µV - 100 µV with a sampling rate of 1K Hz by using nrf52832. I was wondering if I could get advice/help...
Hi,
The code is working normally, but when I include ble_radio_notification_init functionality. Then it crashes (hardfaults), on some boards not all.
[19:18:40.550]...
Hello.
We are migrating from SEGGER Embedded Studio (SES) to IAR Embedded Workbench (IAR). SES used Printf as a comment display and output it to the Terminal Emulator. I...
I've previously used Getting Started Assistant to install nRF Connect SDK 1.5.0 on macos and managed to get a complete and functional install.
I'm now trying the new Toolchain...
HI,
I have few queries regarding nRF52805.
Is there any specific pin configuration required to enter nRF52805 in to programming mode?
What is Adverting connectable...
Hello. I am conducting experiments with data transmission via the Enhanced ShockBurst protocol with BMD-340 modules. Transmission parameters: 2 Mbit radio channel speed, 512...
Hello Sirs
I want to use the serial port of nrf5340-Dk to get some serial data from a sensor and transmit this
data Via a peripheral connectable config by nrf5340-Dk ...
I'm trying to access an SD card with FAT_FS, with no success. I hooked an analyser to the SPI, but it's completely dead. I'm using NCS v1.6.0.
Is there something...
I am very new to BLE development, and am building my application on top of the ble_central\ble_app_uart_c example.
I have this tag defined at the start, with the other global...
Dear Nordic Engineers
Our customer uses NRF52810 with a PA chip, the model of the PA chip is RFX2401C. The attachment is the manual of the PA chip. The hardware connection...
Dear Nordic,
We use CONFIG_BT_CTLR_DATA_LENGTH_MAX definition set to 251 in our project to be able to send large data packets. Still, when migrating to nCS 1.6.1, we've...
Hi, Nordic team!
I want use RTC with Prescaler 32765 for generating Tick event with 1s interval. Could you help with calculation of jitter for Tick event in microseconds...
Hi,
I need to reduce the consumption of the peripheral_uart sample on a nrf5340dk, I use nRF Connect SDK V1.5.0.
At the beginning, I measured with an ampere meter 591uA...
When I program my external board via the nrf52dk the programming is much slower then when I program the nrf52 chip on the devboard. Is this normal behaviour and if not how...
