I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
hi,
After the TX interrupt event occurs, on_radio_disabled_tx() is executed.
There is a timeout event for receiving an ACK. I noticed that the timer timeout was set...
Hi
I'm a bit unsure as to how to interpret the documentation. It's my understanding that zephyr v2.4.99 is an unstable development release. But it seems to be the only release...
Hello,
4-byte long SPI messages, "1234", are sent to nRF 52DK. The code in DK is attached below. The XFER_DONE event is created before the message ends, which happens very...
I thought this would be rather simple as I would design a BLE peripheral in the usual way but the source of data for the peripheral comes from a sensor sending nonconnectable...
Hi,
I am exporting SAADC example to NRF52840 Dongle and I can see this structure:
/** * @brief Input selection for the analog-to-digital converter. */ typedef enum { NRF_SAADC_INPUT_DISABLED...
Hi,
I get read service content retained after reset, and it is read by the central before I get the chance to change it. Please advise how to clear it upon restart.
Thanks...
I want to create two switch EP(if it is possible I would like to it as much switches as possible).
I am using WIndows 10 with Segger and nRF COnnect SDK v1.5.0.
I tried...
Hi, We're trying to simultaneously run BLE Eddystone and connectable mode in our application. Our device is advertising it's ID but every time I try to connect via BLE from...
Hi Team,
regarding my application I need to switch the reference voltage we are taking two deferent reference voltage Ex: one for 2.25 and another 0.75 so we have requirement...
Hi,
I am working with nrf52-ble-app-uart-relay example taken from Nordic Playground github. I have SES IDE, nRF5_SDK_16.0.0 & nRF52840 DK. The central part of the relay...
Hi
Having the nRF5340DK board and following few examples from the nRD SDK Connect. After programming the application core, need to program the network core using the hci_rpmsg...
Hi, I already read more threads about this issue. How to program the nRF52840-Dongle. Most threads go to far in details, where my knowledge ends... I just want to run a simple...
I am trying to include software support for the ST LIS2DE12 accelerometer chip which is found in V1.5.0/zephyr/modules/kconfig.st as
config USE_STDC_LISDE12
bool
V1...
Hi,
I'm looking for the source code to the program that came on the Thingy91
I have not been able to find the source anywhere in the documentation
or sample code....
I am trying to port an nRF51 project that runs on the nRF51 DK using Keil to the nRF52840 DK using Segger Embedded Studio. Clearly the best way to start is to take an example...
