Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I am doing a design with this component MP06003, but I don`t find this in the distributes in Argentina.
I am looking for this components with others distributes...
Hello Community! I've recently switched from Master Control Panel to NRF Connect. I want to use my NRF51 Dongle (PCA10031) with NRF Connect. Therfore I deleted the existing...
According to eval kit reference BOM list a TDK MLZ1608M100WDT25 10uH coil is the only one on list. Is there any other suggested coil models tested by Nordic? Just wondering...
We are designing a custom antenna for the nrf52833-QIAA. Could you supply the output impedance of the ANT1 antenna pin so that we can run an HFSS simulation on our layout...
Dear Members,
I run 3 devices,
GPS on libuarte1
LCD on SPI2
Sdcard on SPI 1,
I'm using ANT and softdevice 340,
When I run LCD and SDcard outside the main loop...
Hi,
I am having problems with the ble_advertising_int() function. It returns a return code of 12 (NRF_ERROR_DATA_SIZE) which is returned by ble_advertising_init() -> ble_advdata_encode...
Hi I ran in some problems with my BLE fragmentation. I want to send data (files) up to 6kBytes over BLE (Bluetooth 5 on nrf52840 to another nrf52840). My project is based...
I'm using PCA10056 (nRF52840 DK) for a project. First-time user, so little experience with this board.
I need 1.8v level SPI signals from the PCA10056 since I need to talk...
Hi
what is the current consumption for LPUART (when there is no event - let's say it is sleeping) on nRF9160 and on nRF52?
https://developer.nordicsemi.com/nRF_Connect_SDK...
Hello,
I have a problem regarding the connection to the cellular network of the nRF9160DK.
When I boot up the device and I have uploaded a code to connect to the network...
Hi,
We have a custom software for our custom board. And would like to investigate a little in the AT commands going to the modem and the responses
is there a config...
I am using Connect SDK v1.7.1 and Ozone v3.26b. When I click "Debug with Ozone" in VS Code, I receive the following warning in the Ozone console:
I am able to correct...
Hello,
While developing the device, I found that the SAADC module on the NRF52833 incorrectly measures the voltage on the NRF_SAADC_INPUT_VDD channel if you set the REGOUT0...
