I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hello.
I need to transfer files from a phone to a BLE peripheral device. I have a small FatFS filesystem on an external flash chip on the device, and I'm now trying to decide...
Hi,
I have just setup the nRF Connect SDK for the first time. I am running Ubuntu 20.04 in a Virtual Machine. I followed the instructions in the "Getting Started Assistant...
Hi!
I'm trying to prepare FOTA firmware using instructions provided by: FOTA upgrades but it seems not working.I have couple of issues and questions. Please help me.
My...
Hello,
I have been experimenting with the new VSCode extension for the last week or so and I've noticed some issues. I understand that this is a currently a beta release...
Hello,
Is it possible to receive a review for a board i'm developing??
This board is to be used as a Raspberry Pi Hat to be able to communicate using UART between RPi...
How to recover communication due sequence number. (Could be due of PYACI serial hardware changed/dammaged). Is there any command to reset or know sequence number of node....
Hello all,
I'm developing a BLE CGMS application based on the experimental example on the SDK folder.
Now I working in the timing characteristics and I could see that...
It looks to me like there's usage of the 32 bit milisecond timer in the mqtt client.
It seems to me that mqtt_elapsed_time_in_ms_get(...) could calculate an incorrect elapsed...
We're using the nRF9160 with an external main microcontroller, and communicating with it over SPI. We're evaluating the lowest power modes of our custom hardware to make sure...
1. I want to minimize current consumption (5uA - 10uA) in nrf52832.
2. We are using the soft devices in it.
3. Please tell me all possible SDK configuration settings for...
Hello all,
I have a BLE central application based on nRF Connect SDK V1.6.1 and a BLE peripheral application based on nRF5 SDK 17.1.0. The peripheral wakes up on interrupt...
Hi
For the qualification we need to know the values of the parameters listed below. Our hardware uses a nRF52805 and can operate in both ESB and BLE mode.
Operating...
Hello Devzome Users,
I have a problem with running my codes on other computers. The project runs on my PC very well which I coded original.
I would like to test it on...
Hello Nordic,
I've acquired several nrf52-dks and I use them almost exclusively to flash with nrfConnect on the PC.
To learn more about nrf programming I started with...
Hi all,
May I know is the antenna array a built in in 5340 DK or not? According to https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/direction_finding_connectionless_rx...
