Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
I am currently working w/ a project that utilizes TrustedZone and PSA Protected Storage to read/write to internal flash that's accessible only in the secure partition (I'm...
Situation : custom nrf5340/nrf7002 board (very close to production...). Main image is overflowing available internal flash (with a MCUboot 64kB partition).
Secondary slots...
nRF52832 & nRF Connect SDK 2.6.1
We would like to reserve some internal flash for user configuration data that would be written in production like
and read by FW but...
Hi,
I am working with nrf5340 with the Zephyr OS. I created a custom data section in a custom linker file.
.my_data_section : { PROVIDE(__my_data_section_start = .); KEEP...
Hello,
I spent a solid two hours debugging an interrupt pin that was not working, to discover that the problem appears when configuring a callback in another part of the...
I have been bringing up an application on nRF54L15-DK, and about 50% of the time it hardfaults on initialization. I tracked down the cause to a branch to address 0, caused...
I am currently using DWM3000 EVK with NRF58240DK for a UWB indoor localization system. I want to use the timer to setup a localization period for each tag node. I tried several...
I am currently working on direction finding using the nRF Connect SDK in VS Code. I am using an nRF52811 custom board, and my logs work properly. I wanted to include timestamps...
Hello. I'm trying to control led in gpio pin in addition to LED pin in npm1300. I don't think you need to use resistance in LED pins, Is it the same when using led in gpio...
I am using NRF Connect SDK v2.5.2. Sometimes, after I factory reset my Zigbee router device, it will immediately join a network with PAN ID 000000000000. I get this with my...
I'm trying to move my nrf9151 project over to sysbuild (SDK v2.9.1) but when I try to use a custom board definition, the code fails to start up.
So far I've tried debugging...
I found this pretty old post devzone.nordicsemi.com/.../switching-between-apps-with-dual-bank . Currently I am building two different zephyr projects and selecting between...
Hello,
This is long shot more than anything else but are there any instances of a video coded (mp4, AVI or similar) ported over to the nordic/zephyr platform. I can't see...
I got an nrf52840 dongle(PCA10059) and I'm trying to run the official usb-hid-keyboard example on it, but the compilation is failing. What could be the cause, and how should...
Hi,
I want to make an I2C communication with an NRF5340 DK as Master and an NRF52840 as Slave, but all the example i found in I2C communication it use the slave adress...
