Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hello
According to Enhanced ShockBurst (ESB) documentation , to stop the ESB module you need to call esb_disable(), but it also says that you need to check if the module...
I have a project where we did not populate the external oscillator for our custom board which has an nrf5340 on it. I did most of my BLE testing on the nrf5340 devkit and...
Hi,
I designed a custom PCB with the nrf5340 CLAA chip and am testing out the board. I want to flash a simple project of lighting up the on-board LED (the LED is connected...
servo uses pwm0 device, channel 1 in DTS file.
But in its pinctrl file, GPIO P0.13 uses PWM_OUT0 which is channel 0.
It should be changed to " psels = < NRF_PSEL ( PWM_OUT1...
Sorry for the inconvenience!
I have downloaded V2.8.0 nRF SDK, and I use this command to build light bulb project:
west build -p always --build-dir nrf/samples/matter...
Hi, Can you please help in connecting the nrf52840 DK with CMW500 and to measure the RF power at different levels of nrf. (For example, at 8dBm, 4dBm, 0dBm, -40dBm). In this...
Hi,
I'm using the nRF54L15 DK (non-secure, NCS v2.9.1) to generate a 100 kHz PWM on a GPIO with TIMER00 (128 MHz, 1280 ticks, 2.5%–20% duty, 32–256 ticks). GPIOTE, DPPI...
I have a test application which uses the "Azure IoT Hub" library. I have set up the IoT Hub, Update Account, update instance, etc. The device does successfully connect to...
I am developing using the nRF5340DK with Segger v5.68 and SDK within toolchain v1.9.1. My project works perfectly on my old PC, but after moving to a new PC with the exact...
Hello, I would like to implement a simple RSSI-based distance measurement function using the Periodic Advertising Samples（periodic_adv & periodic_sync）. In the scan callback...
Hi,
I am trying to build an application using the nrf54L15-dk board and want to use the board as a controller. I run the application on the external host but got an error...
I don't know who's in charge of Dev Academy, but the nRF Connect SDK Intermediate Lesson 9 -- Bootloaderse and DFU/FOTA section looks like it was written as a back burner...
Hello, I am trying to save some sensor data based on my current state of the device. I want to log IMU data and timestamp into my external flash (MX25R64) with littlefs file...
I am using a custom board with an nRF52840. For OTA updates, I’m using SDK 17.1.0 based on the sample codes:
Bootloader : secure_bootloader
Application : A custom...
I am developing with thingy53. I would like to enable BLE function, MCUboot and littlefs file system at the same time. I am using SDK and toolchain v2.7.0 and sysbuild as...
