When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I want to use the external flash on the nRF5340 DK using SPI as the board I'm developing for will not have QSPI. I used the littlefs sample which has a lot of the settings...
Hi,
I'm trying to implement a PRE_KERNEL1 timer (with top priority 0 ) to toggle an LED.
I’m able to control the LED using registers, and now I want to add a timer layer...
I want to send a custom message using a custom Property ID in Mesh Sensor observer example. How do I add a custom Property ID? Currently, I am using #define CUSTOM_ID 0x1234...
I am debugging an application on a nRF5340 DK using nRF Connect SDK from VS Code. (Toolchain/nRF Connect SDK v2.9.0), everything up-to-date.
The build is "optimized for...
nRF52840, nRFSDK 17.0.2, SoftDevice S140 v7.2.0
Hello! We're turning on SoftDevice and using the PA/LNA pin control to drive our FEM. Then, we disable SoftDevice and issue...
Hi,
I found a bug in the init part of the LIS2DU12 driver. The driver tries to reboot the LIS2DU12 sensor using the SW_RESET bit in CTRL1 register even if it is not in...
Hi,
I'm trying to synchronize a process using an nRF52833 dev kit using a Zephyr event.
The code looks like this:
The first routine sends an event and the second captures...
I am working on an nRF52-based device using nRF Connect SDK (NCS) version 2.7.0. The device is configured to enter deep sleep every 60 seconds and wake up via a GPIO interrupt...
Hi,
I'm using the nRF Cloud multi-service application on my Thingy:91X.
I am using the Serial Terminal to see what networks are available, but when I go to attach manually...
Hello,
I've been working on a project using nRF52832 + NCS 2.1.1 including BLE and some sensors : MAX86150, MAX30205, MP34DT05, LIS3DH
I'm sending data of these sensors...
Hello! What are the steps I need to take to switch from BLE protocol to lets say the Gazelle protocol? Is it as simple as disabling the Softdevice? If such a function exists...
We are finishing up development of our product and looking into creating our Bluetooth listing. We are using the NRF52840 SoC (Fanstel BT840F model) with softdevice and NRF...
The NORDIC tutorials are great for demonstrating how to use GPIOs to drive LEDs and read buttons.
However, I need an 8-bit bus to exchange bytes with an external display...
Hi,
I am working on an application using the nRF52840 with the Quectel BG96 modem. I can successfully communicate with an insecure MQTT broker using the BG96 modem. Now...
Hi!
I'm making a new board using nrf54l15 and I found the following issue:
/* * PWM signal can be exposed on GPIO pin only within same domain. * There is only one domain...
