Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi,
(see image below for clarity of this text)
In our product, we have this requirement. - be able to update the application on the nRF9160. - be able to update the firmware...
I'm not sure what happened to my SES but every time I try to debug I get a message saying that my image is out of date even just after having rebuilt it. Any idea what may...
Hello,
I’m able flash my code to the nRf52832 with no problem. At this point all is well. The problem occurs when I power down the device and then power up. On power up...
Hi,
I was merging the files of peripheral hr in ble mesh chat project
how to add new .a project in nrf connect sdk using segger embedded studio and also how to include...
Have a catch-22 here.
Here is my code:
When I call nrf_sdh_enable_request() it returns the error '0x08 which is SoftDevice already enabled according to the documentation...
Hi everyone,
I use to use the nrf52840 dev. board with the SDK16 examples. Now I am facing a problem with all the BLE peripheral examples
1. When I build and run in release...
Hi there,
for a customer of mine I have to programm a Arduino 33 BLE but not using Arduino IDE but use the Nordic SDK.
As it is a normal nRF52840 (inside an Nina-B306...
I am currently working on a project in which I will need to increment the pwm up to full cycle in 'x' number of steps and then be able to step down 'y' number of steps when...
I'm using app_scheduler to pass UART events in the "main thread". I'm storing multiple data types in a struct (arrays, integers) and I've set the max event size to the size...
Hello Team,
I am using the OT-nRF52840 source and working on the end device. I want to add the I2C(TWI) support in my end application, but as soon as I add any API it shows...
My problem is similar to this
https://devzone.nordicsemi.com/f/nordic-q-a/64696/projects-for-writing-into-flash-memory-does-not-work-on-nrf52840-dongle/264746#264746
except...
Can a "Pin Reset" recover the nRF52810 part if the part has encountered a slow voltage rise, greater than 60 ms, from 0 - 1.7V (described in the image below)?
Hi, I am new to nordic and zephyr and I have a sensor (Melexis - MLX90641) and I would like to test it on a custom board using nRF9160.. I add the sensor into the dts files...
When I open the nrf connect sdk project, it goes like this,
How can I fix it?
Creating solution direction_finding_connectionless_rx.emProject cmake -GNinja -DBOARD=nrf52833dk_nrf52833...
