I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
When I open the nrf connect sdk project, it goes like this,
How can I fix it?
Creating solution direction_finding_connectionless_rx.emProject cmake -GNinja -DBOARD=nrf52833dk_nrf52833...
Hello,
I am preparing to develop a design using the nRF52840 and would like any guidance or consideration for an LDO usage. I have found some previous mention regarding...
At 1Mbps, UART will lose data when receiving. When I set it to 230400bps, it works well. I looked at the SDK code and found that too much time was spent in the receiving code...
Hi,
I had asked a question here few months back, about the maximum RSSI that can be seen on the nRF52832 chip.
https://devzone.nordicsemi.com/f/nordic-q-a/73578/maximum...
Hello.
We have several of our own manufactured boards, containing the nRF9160 cellular modem chip.
We use it for HTTP and HTTPS connectivity, on an application based on...
Hello. We are developing using nrf52832 (S132 v7.0.1, SDK v17.0.0).
I'm looking at how to encrypt a string with AES CBC. Below is the code we are considering.
Currently...
Hello.
I'd like to split an external QSPI flash chip so that part of the memory is accessible as raw blocks, and the other part holds a filesystem such as fatfs. Essentially...
Hi
I am using NCS version 1.5.0, I need to drive the GPIO pins of NRF5340 DK using the below library
"#include <nrfx/hal/nrf_gpio.h>"
While trying with this header...
Hello,
I am trying to run the example projects "ble_app_uart" in SDK17.0.2 on nRF52833DK, following the guide shown here: https://infocenter.nordicsemi.com/index.jsp?topic...
Hello,
1- we are using button-less secure bootloader.
2- Have successfully download our application image to the target via nRF Connect mobile App.
3- When target is...
Hello All,
I tried implementing basic cluster, Analog Input cluster and Power Config Cluster. My end application is report "measured tank level" using zigbee. For which...
I am trying the https_client sample and I can get it to work unchanged.
But I would like to connect to a different site than www.example .com.
As far as I can understand...
I'm running the ble_app_pwr_profiling example from the nrf5 SDK (16.0.0) and softdevice (s140 7.0.1) on a nrf52840DK (pca10056 2.0.1) and measuring power consumption using...
Hello, I am developing an application on nrf52840 using SDK 17. My application has a bootloader and sometimes when my application is restarting due to a command I send (using...
