I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
The BLEJack nrf51 sniffer firmware is a BLE sniffer/jammer/hijacker. If you google you will find the repo and the defcon presentation.
The author claims you can sniff access...
Hi,
I am facing the issue of sending 8210 bytes of data to my slave device.
I am using NRF52840 interfaced with the MAX32664 maxim sensor hub.
I tried both approaches...
We are thinking to evaluate both the U.FL and Trace Antenna options on a custom nRF52840 prototype board.
1. Referring to this discussion, point 3 is about provisioning...
I want to use mesh configuration ( Bluetooth mesh submodule) to save data to the flash memory of nRF52840. The code works fine and I can save data to flash using mesh_config_entry_set...
Hi, I'm having problems with compiling the gazell_dynamic_pairing example with arm-gcc compiler for nRF52840 Dongle. I have already migrated other gazell and esb examples...
Hi,
I have this generic register read function to handle communicating with my sensor, and during initialisation, it works fine. However, when I try and request a transfer...
Hi! I'm trying to setup mesh network and get data from sensors thought SensorClient SensorServer via ProvisionerNode.
My Nodes info: - Provisioner, UnicastAddress 0x0001...
Hi,
I'm using DSK 17.0.2 on the nRF52840 DK.
I followed the instructions for a buttonless serial DFU:
1. I cleared my board (nrfjprog -f nrf52 --recover)
2. flashed...
Now I meet a problem: when the chip of nRF52832 is power off, but supplies power to one GPIO pin of the chip through resistor voltage division, then I found the voltage of...
Hi everyone,
I'm currently trying to the get UART logging running on the NRF52832, but fail to get the SDK working.
My settings are as follows:
#define NRFX_UARTE_ENABLED...
I want to use GPIOTE implement soft uart on nrf9160 Because it can use interrupt to receiver and data
Any kind man give a example here. that will be thanks a lot
Hi all,
I new to Nordic Semi and recently got started with nRF9160-DK. I've gone through the getting started guide and am looking for suitable tutorials, and examples to...
Hello,
I wanted to show a colleague all the great features that the Cat Tracker has. I am working with Settings. The most important feature exists -- when I change a setting...
I'm working with SDK Release 1.5.1 and Toolchain Version 1.5.1
I'm trying to configure the serlal_lte_modem example to support the HTTPC feature and switch to UART_2 for...
