Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
hi
I want to know where the gazell control the GPIO06, i connect a LED with this pin ,and its blinky when send data failed .
I used to see it controlled in somewhere but...
Hello,
in my design I used the antenna swra117d from Texas.
I am able to connect to my custom board with the nrf52 dongle and the nrf52 DK.
Unfortunately I can not connect...
I followed the recommended steps and got the at_client solution to build and flash in Segger Embedded Studio with tag "v0.4.0".
I installed it onto my board, and but didn...
Hi,
I'm currently programming a custom board using a nRF52832 ( using this wiring ). Everything was working great but I tried to play with SAADC and maybe did a wrong...
I am using the link below
https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v15.3.0/getting_started_softdevice.html#getting_started_sd
with 3 options...
I'm having some problems getting the sections/observers to work properly. Using SDK v15.3 and Crossstudio for ARM v4.4.2
If I break at ( nrf_sdh.c )
I can see that the...
Hello, I have just started using nRF52840 DK and previously I have used development kits from different vendors so, I was wondering when developing which resources are available...
Hi All
I know this is stupid but I can't figure it out - either I've missed something obvious or not connected something properly (or at all).
Using the PCA10040 nRF5...
I have developed a custom board with NRF52810 (Rigado), a standalone CAN controller (500 kbaud) and serial communication (57600 baud).
The SW is based on the BLE_APP_UART...
Can anyone tell all the potential reasons for stack corruption? I'm debuging a problem where sometimes there is no stack trace when putting a breakpoint on the first line...
I have a project based on SDK 15.3
I've set #define NRF_LOG_DEFERRED 1
The project generates a high volume of log output over RTT
NRF_LOG_FLOAT_MARKER is a macro that...
Hi, I am using the nRF51822 with SDK 12.3.0
I am trying to make use of nrf_drv_spis driver included in the SDK.
My purpose is to have nRF51822 constantly be RX-ing over...
While investigating my stack corruption issue , I noticed that the RADIO_IRQHandler is always called twice in quick succession:
But the NRF_RADIO->INTENSET register only...
I'm trying to communicate between two devices (nrf52840 and teensy 3.6) over RS485, but I'm having some issues using the UART library in the SDK. I'm trying to create an interrupt...
Hi,
It all happened today after being used the board for a month. when I tried to turn on the board it does not blink LED5 nor does it show up in the device manager. I to...
