Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
I'm using Rigado BMD350 evaluation board. I'm printing to serial port (COM3, speed 112500) using NRF_LOG_INFO.
However, the logging does not appear until debugging is...
In a recent project, me and my team have been trying to send data from 3 PTX devices to a single PRX device (the devices are all nRF24L01+) at a constant rate of 1600Hz from...
hi all!
Like two of my predecessors, I am trying to put a CR95HF into operation. I chose the nRF52832 DK as MCU (SDK 15).
[thread= https://devzone.nordicsemi.com/f/nordic...
I changed only source clock part to internal clock and it doesn't do advertising. When I debug it, it starts to run. When I finish the debug session advertising stops again...
Hi,
I've built a custom board with nRF52832, without other MCU like PCA10040. I use a FT232RL to bridge the USB to nrf UART, flashed nrf5 uart connection firmware ble_connectivity_s132_uart_pca10040...
Hi, I using nrf52810 with custom BLE profile and 4 sec advertising + continuous RTC. Device is battery powered (750 mAh) and PMDC motor equipped. Most of time (90% of day...
Hi,
I am designing my custom board with the nrf52832, which would perform the BLE and I2C functions. I wonder what necessary and basic peripherals it needs, like crystal...
Hi,
I would like to synchronize 2 Sensors with one dongle. So the problem is that we have two sensors and we want to start the measurement at the more or less (1 ms) exact...
Hello,
I am new to BLE as a technology and have a question regarding how Peer Manager handles bonding.
As I currently understand, the function of bonding is to enable...
Hi,
I want to use nRF52832(PCA10040 board) to communicate with nRF24L01+. I program the example application( \examples\proprietary_rf\esb_ptx)(SDK v15.0.0) on the board...
Hello. I'm developing an application with a custom bootloader and I'm using "settings" data structure placed in FLASH. Because we can erase only full pages, the first page...
Hi.
I want to implement multirole on the nRF52832. I want to advertise beacon data while scanning. So, I modified ble_app_uart_c in the ble_central example. Below is a description...
Hi,
I try to program hex file with openOCD. The flash part is written without any problem. OpenOcd only fail to write the UICR registers beyond 0x10001200.
However it...
Hello,
Which one of the following statements regarding " sd_ble_gap_connect " function call is true:
(1) Can sd_ble_gap_connect function put the central device into initiating...
