When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I am following all the steps given here: nRF Sniffer for 802.15.4 but my zigbee sniffer did not show up. When i did the steps given there for ble sniffer it showed up. steps...
Hello,
I am new to developing with Nordic products and I have a question regarding the components in the antenna matching network. I am designing around the QIAA QFN-73...
Hi,
I am trying to use the nRF915-DK with a GNSS Tracker application. Everything works fine, but, I am not able to set the nRF9151-DK properly for utilizing the board...
Hello
I'm preparing the certification RF testing software on our product 4MOD9192 using nRF7001 for wifi function.
During the certification test process, we need to...
Is it possible to add custom regions for a project to be used by the Partition Manager? I see how and where regions are defined, as shown here , but I'd like to use multiple...
I have a nrf9151dk with a nrf7002ek shield. The nrf9151dk has the DECT NR+ PHY firmware running on the modem core.
I would like to do Wi-Fi positioning with the nrf9151dk...
Hello,
I am using the nRF52833 - DK and running the USB CDC ACM example. I can transmit and receive data with the example. I noticed that when receiving data I am only able...
I am using Zephyr 3.7.0 with the Nordic-provided low level link layer (LLL) code on an nRF52840-DK. I'd like to set a breakpoint on rp_comm_rx_decode() ( https://github.com...
I want to connect two nRF54L15 development boards using I2C protocol. Is there any sample in nordic SDK v2.0.8 or v2.0.9 that I will help me to set up nRF54L15 DK as a master...
Hello,
To preface:
HW: nRF9151DK
SDK/Toolchain: nRF Connect SDK v2.9.0
I am new to Zephyr (first project)
When using a nRF91 modem, it seems that CONFIG_POSIX_API...
Hi there,
I would like to get information regarding the possibility of implementing 5.1 isochronous audio streams on the nRF5340 Audio DK development kit. According to this...
I've been using the function nrf_ble_scan_filter_set for several years with developmental hardware based on the ble_uart_c example, so I've reviewed that example thoroughly...
Hello,
I'm not able to sniff BLE using your tool
I tried to configure nrf sniffer with nrfutil.
OS: MacOS 15.1.1 (arm)
Wireshark: 4.0.17 (it seems the actual version...
Hello
Is is possible to enable MCUBoot image compression on nRF52832 ?
I tried to enable it following this blog post but I got a compilation error :
Compiler insulted...
