I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I'm trying to test the overall pwoer consumption of my setup (nPM1034EK and nRF54l15DK) using the PPK2. As I've started this, I've gotten far higher numbers that I expected...
After I reset the kit (custom equivalent to nRF52DK) it advertises, and I can connect from the BLE Standalone App on my Windows computer. But it only advertises for a short...
I recently bought a fanstel blg840 device, and I have programmed At client firmware in nrf91 and custom code into nrf52, but the problem is nrf52 is sending at comments to...
I am trying to work with my flash deivce in my code. for some reason:
const static struct device * int_flash_dev = DEVICE_DT_GET ( DT_CHOSEN (zephyr_flash)); doesnt work...
I have been having a series of issues with programming from nRF Connect using a J-Link programmer. I have made a couple of other recent posts and in each of those, I thought...
hi,all
I used to use nrf54l15dk board as a client server, want to connect to a bluetooth remote,and get bluetooth remote notify message;
I use sample "central_hids...
Hi guys,
I have MQTT v5 up and running but I am currently trying to implement one-way TLS then mutual TLS once it's completed. I am not too sure what I am doing wrong but...
Hi:
My environment is: Windows laptop, nRF52 DK (Peripheral), nRF52840 Dongle, Mobile Central (iOS and Android), and Wireshark nRF Sniffer for Bluetooth.
Peripheral sends...
Hello all,
I have problem with flashing the code. It gives me memory protection error.
Steps I followed for creating firmware and flashing:
1- I took a sample from nrf...
I'm working on a product prototype using the nrf5340 audio dk to send audio via Auracast. We started from the nrf5340_audio application, as it implements a large fraction...
While testing UART communication between a Seeed XIAO board and the nRF9151 DK, I connected the following pins: - XIAO 3.3 V → DK VDD - XIAO GND → DK GND - XIAO TX → DK RX...
Hello,
In the nRF52840 datasheet, some pins are explicitly marked as “low frequency I/O only.” However, I couldn’t find any similar indication in the nRF54L10 datasheet...
Hi everyone,
I’m testing a custom nRF54L15 board with BLE, but it gets stuck inside bt_enable() . To debug the issue, I checked whether my 32 MHz external crystal (HFXO...
Hi, I want to use the external flash on nRF9151-DK (gd25wb256). Having set all the necessary files (prj.conf, nrf9151dk_nrf9151_ns.overlay) and some parameters in the main...
