Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
I use nRF52832 as a central device. I also use ble_app_uart_c as a SDK(17.0.2) . I would like to connect my peripheral which is my phone(iPhone 6) and i want to see my phone...
Hi,
I'm on pre-product of BLE Advertisement packet scanner.
My product is gathering the adv packets from a bunch of BLE tag about 20~30 tags.
So, I use two nRF52832...
Hi,
I want to add bonding information manually.
1.can I assume IRK key will be constant for multiple peripherals?
2.if IRK only key is available, can i add it to peer...
I am finding that the voltage measurement is about .52 volts off when measuring Vdd I have set up a power supply and connected it to external power. My saadc is set up with...
Hi,
I am starting to finalize a development stage and was looking at the current consumption of my device. I noticed, that when something connects to it and is starting...
Hello there,
we get the following assert:
"00> <t: 480881>, app_error_weak.c, 98, Softdevice assert: 88996:0"
The board is rebooting constantly after 3 ... 7 minutes...
I tried to build the example project for UART serialization demo, "ble_app_hrs_pca10040_s132_uart". It failed with 3 errors, see attached image.
It is SDK 17 and SEGGER...
Product: nrf52840 DK
Softdevice: 17.0.2
Hello,
I would like to start with a very humble statement that I am new to this nrf52 SoCs and would appreciate any of your...
Hey everyone,
I am playing around with Nordic Cloud, Thingy:91 with the Asset Tracker v1 and the Nordic Cloud RestAPI.
I happened to see in the process, that the unix...
Hello,
I contact to you because a customer bought the development tool part number n RF52-DK, and one received the product, they noticed that there was on the box of the...
I use nRF52 DK as a central devices and i have also other nRF52 DK and use for a beacon. I would like to show my beacon's RSSI value on the UART Terminal(Realtek,Termite exc...
Hi,
I have done buttonless DFU in Custom board using NRF52832. My code with DFU is working fine in the nrf52832 Development kit. While I am trying in a custom board. My...
I'm developing for nRF52 DK
using SDK 17.02
Segger 5.10b
I'm developing a service to read pin 12 where I'll have a square wave signal of about 60Hz. When I tested my...
