Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
I am running custom firmware on a custom board using an nRF52832 chip. I have encountered an issue after migrating my project from SDK 14.2 to SDK 15.3. The issue is that...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Hello,
Since I migrated from SDK 13 to SDK 15.3 I can not see anymore print of NRF_LOG_DEBUG, NRF_LOG_INFO, NRF_LOG_ERROR and so on, on segger Jlink Viewer.
I have tried...
Are the following arguments correct?
data_rate <RADIO_MODE_MODE_Ble_1Mbit> or <RADIO_MODE_MODE_Ble_2Mbit> and so on.
output_power <RADIO_TXPOWER_TXPOWER_Pos4dBm> and...
Hello,
We are using the nRF52832 and 2G(GSM/GPRS) module to build up one IoT product. We got a disconnect between nRF52832 with other master instance(mobile phone APPs)...
Using Softdevice s140 v6.1.0 nRF5 SDK v15.2.0
I am trying to write to the flash, here are my read and write functions:
Two problems:
The write function does not...
Hi,
I've added an instance of the Generic Power OnOff Setup Server to an element and I can see it and all the models that it extends, i.e. (Power OnOff Server, DTT Server...
Hi all!
I'm trying to run the light_switch example (client and server), and i cant complete the provision process.
I'm using my phone and Nordic app for provision, when...
Hi.
I just wonder how can I send string message through ble.
I will use raspberrypi as server. You can check whole code below.
It works well with computer bluetooth...
I am working on nrf52SDK. For my curiosity i wanted to know the BLE stack version.
Is there any calls available to query the soft device(S132) to know the BLE stack version...
Hi all,
I have a very strange problem with the Buttonless DFU service. For my project we have two different builds, one debug and one "release" build. The debug build sets...
Lately with 2 different nrf91DK boards I have, I can't program them unless I do a full erase first.
I did see this post here: https://devzone.nordicsemi.com/f/nordic-q-a...
I am shopping for a Bluetooth module that will accept Bluetooth streaming from a personal device, supporting A2DP V1.3 minimum, decode it, and output an I2S stream. Many Asian...
Hi,
I have a project running on a custom board with the nRF52810 populated and I make use of a GPIOTE input interrupt. The code works fine for the nRF52810, but not when...
Hi
There are two things I need help with. I am using Segger Embedded Studio on Linux(16.04) and SDK 15.3
1. I am using nRF52832 DK to debug and flash to external(custom...