hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Greetings, I am developing an application for the NRF52840 in a RAK Wireless RAK4631, using the Arduino BlueFruit libraries.
When I monitor NRF_RTC1->COUNTER variable, it...
Hello everyone,
Because of problem with availability we were forced to change our ready-for-production project from nRF52832_xxAA to nRF52832_xxAB which has 2x less FLASH...
Hi, there
I am using nrf52832 chip on a custom hardware and also using softdevice 132 to send data to an app.
I need to send data from app to MCU and vice-versa and...
Hi
I am using the nRF52832DK and the BLE_App_Blinky.
I have a stable BLE connection to a phone and then I try to close the connection inside the nRF with sd_ble_gap_disconnect...
Hi, I am trying to implement Azure FOTA using your libraries. My source code is a combination of the Azure iot sample and the Azure fota sample + some necessary alterations...
As I know,the New Order Code of nRF52 Series has added Access port protection Controlled by hardware and software function, the earlier order code : Access port protection...
Hi, I'm working on updating nRF9160 modem firmware update.
I have update modem[mfw_nrf9160_1.3.1.zip] using nRF connect Desktop application and read partition using nRF...
Hi
I run nRF connect SDK 1.7.1 and have a custom nRF9160 board.
I'm trying to get the I2C peripheral to work with my own hardware.
I have read and googled all tutorials...
Hi,
Can I use the hex file compiled for nRF52810 for nRF52805 directly ? Please note that I am not using any peripherals other than radio.
Can I use the nRF52810 build...
We use the nRF24L01+ in a dedicated RX mode, and it is preceded by a power splitter, filters and LNA. In order to run some system calculations, I'd really like to know the...
We are using nRF52840 on a custom board with nRF5 SDK v15.3.0.
Our application uses the NFCT driver (nrfx_nfct) along with nfc_t2t_lib_gcc.a to emulate a NFC tag with some...
HI,Therd:
I used the mesh sdk 5.0.0(BLE SDK 17.0.2), and run the example light_switch_server_nrf52832_xxAA_s132_7_2_0.emProject. when i use the nRF Mesh app on the phone...
Hi,
I am evaluating nRF53 for ZigBee in a Linux application that implements a MQTT-SN Gateway. I am interested in learning about Linux board can connect to the nRF53 (USB...
using nRF5 SDK 17.1.0
Segger
I need some understanding of the QDEC. if I connect a motor that has a A/B output at a 5KHZ rate.
what is the maximum rate at which the...
