hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hi,
I have two sets of hardware, one is nrf52840 DK, and the other is my own board. I use the same program, update package and mobile phone. When using nrf52840 DK, the...
I am using below base example on my peripheral device to send a string over BLE to a central device:
\examples\ble_peripheral\ble_app_uart\pca10040\s132
I use function...
Hi,
I am working on a custom board using an nRF52840 and developing with SDK5 (V17.02).
I have a serial communications channel to the device which must use UART as I need...
Hi,
sounds odd but is not, I try to run samples and my own project on a nano 33 ble, and with the first upload of blinky it seams that the system start and crash (ttyACM0...
Hi!
I'm developing a custom PCB with a NRF52840 which I made a custom firmware based on ble_app_uart example. I test my product with different phones, Android and Apple...
Hi.
I am developing PCB where there is a Wifi module ESP32-WROOM and a nRF52833 connected via 2-wire UART interface (TX/RX only), there is no way to use 4-wire UART because...
EDIT: We found the reason for this and it is a hardware issue. This question can be deleted as it is no longer valid.
-----
Hello,
We are currently developing a...
Hi!
When opening the LTE Link Monitor in nRFconnect 3.7 under Linux (Ubuntu 20.04) only a "whitescreen" appears after I select the device. The application is not visible...
Hello,
I am using NCS v1.5.0 and would like to check is a KMU slot is being used or not. I erased the whole SoC and tried reading the directly the registers, in secure mode...
which pins can be used as PWM output pins in nrf52811.
Can I use them directly or I need to add some hardware to use the PWM feature.
I have an NRF5811 SOM (EYSNCNZWW...
Hi Sir/Mdm, I want to use 1.54 inch e-paper module from waveshare with nRF52840 dongle with Zephyr RTOS. I have read the documentation from Zephyr about the display and noticed...
Hi,
We use the nRF52840 and have now run out of space using debug mode compilation (using CMake from bash).
When we compile in release mode, we get 50% full flash, so...
Hi,
I am using nrf52832 and mesh sdk 3.1.0 with nrf5 sdk 15.2.
We use dual bank approach for our firmware update with the normal nrf5 sdks ble bootloader. But now our...
