Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hello everyone and Good day
I am a fresh graduate and its my first assignment at my job. I have to flash an LED at 1 Hz using NRF52810 BT 5 chip.
There are so many development...
Hi,
I am using nrf51422 interfacing with Ti's CC256MODA Bluetooth so here can you plz tell me how to do pairing with the TI's bluetooth .How to give passcode to the device...
Hi,
for my nrf52840 based project, I need to following peripherals :
2 X SPIM Master
2 TWIM Master
1X TWIS Slave
Given the resource sharing constraint, is this...
Hello guys
The nrf52832 uses 32 Mhz oscillator but I couldn't find much information about the oscillator in the chip document.
Can you give me a datesheet or something...
Hello,
when i try to flash code after loading s132 softdevice using nrfgo studio, i am getting erase failed,cortex-M4 error . but the fresh ble_peripheral alone is working...
Hi,
My goal is to send raw frames to some external device which is not nRF BLE example but commercial used device.
It is using some fixed service with fixed UUID and I...
I doubt Nordic developed a brand new GPS receiver for the 9160. Where does it come from (manufacturer and model)?
The Thingy91 Asset Tracker out of the box example has some...
The Thingy:52 Environment Service uses this structure to represent Temperature.:
This is wrong - it cannot correctly represent temperatures below zero but above -1 ...
pls advise if nrf9160 DK can work in RDP protocol , say the board is in US to work on NBIOT carrier or LTEM carrier . Can it be configured in some way to do evaluation remotely...
Hello!
It seems to me that GCC compiler optimization (-O3 -g3) somehow break the SAADC.
When enabling said optimizations the SAADC no longer gives me valid measurements...
Hello,
I'm developing a gateway and i would like to use advertising packet on sensor side to transmit data but it suggests that my gateway will be in permanent scan. I know...
Hi , I would want to establish a GATT Server application as well as integrate Bond Management Service from glucose example (ble_app_gls) in examples folder of SDK15.3.0_59ac345...
ble_db_discovery_start () returns NRF_ERROR_INVALID_PARAM (0x7)
This problem occurs when two peripherals are connected to one central unit. The two peripherals use the same...
Hey,
I am having trouble validating this idea through research. I was hoping someone could give me some ballpark feedback.
The setup:
- 15 NRF52832 devices on custom...
all set. while in linking stage i am getting
.\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol nrf_sdh_is_enabled (referred from nrf_fstorage_sd.o). .\_build\nrf52832_xxaa...
