Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
HI
Now I am measuring current on the nRF9160DK according to https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/hardware-design/posts/getting-started-with-current...
Hi,
I have nRF52840 DK, and using nRF SDK v17. I am trying to understand radio transmitter example sendpacket().
RTC(1) seems to be used to the transmitting packet.
...
I have designed/copied the suggested circuitry of the nRF9160. I am attempting to program the custom board through a nRF9160DK. It is connected and the command west flash...
Hi,
I am using NCS 1.5.0 and modem firmware 1.2.3.
In my application I need to receive few commands from PC UART (UART 0).
Baudrate is 115200 without HW control. ...
Hello,
I am currently doing an internship and I am working with the nRF5340 DK.
Until now I have tested the "Thread: CoAP Server" and "Thread: CoAP Client" examples and...
Hi my application is working fine with secure bootloader on devkit PCA10056 using nRF52840 and GCC. Now I want to bring it to my target hardware using nRF52820 to get rid...
Hi,
I am writing my own SPIM driver, when I try to send a 2 bytes message and then a 26 bytes message the second message "crashes" after 2 bytes.
But if I send the 26...
I am looking for information regarding usage of UICR in nRF52840. I want to store Board information like board version number etc.. in UICR probably in the customer registers...
I am using Nordic's NRF_SDK_For_Thread_and_Zigbee_4.1.0.
In that example/thread/ncp, I want to build NCP firmware for uart.
Original uart pins for rx and tx are 8 and...
Hi,
I have nCS installed and when creating a project in nCS installation directory (default path), then i have option to choose "Configure nRF Connect SDK Project" from...
Hello,
For my board i would like to remap uart to pin on GPIO PORT 1.
Current:
&uart0 { status = "okay"; current-speed = <115200>; tx-pin = <20>; rx-pin = <22>; rts...
Hi,
We have a requirement to connect a SPI device to each SPI interface present on nRF52840, and we want to write to those multiple devices in parallel. Is there any API...
Hello everyone,
I would like to run the ANT examples "ant continuous scanning controller" and "ant scan and forward" on my nRF52840DK(PCA10056) boards however it only supports...
Hi,
We have a device based on nrf_52840, SoftDevice_132_3.0.0 and SDK_12.3.0, using BLE for communicating to a PhoneApp and UART for communicating to a washing machine...
