Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi, Dev Zone.
thanks for help : )
i'm try to porting DK Board's ble Boanding function to Target Board.
DK is working success.
refer to 16.0.0 SDK and 7.0.1 Soft...
Hi,
I am currently working on updating the examples/dfu/secure_bootloader_uart_debug example in SDK 15.3.0 to do an internal dfu on my nrf52840 DK rather than having the...
Hello,
Out application is using the time slot api to generate ~29ms (35Hz) burst of pulses.
Occasionally, the interval between two adjacent pulses extends to ~35ms ...
Dear Nordic support,
I need to clarify a few points using SAADC for battery measurement - running the ble_app_proximity application without modification. I measured the...
hello, i hanve a problem when i use usb transfer data to pc with ep1, sdk 17.0,nrf52840dongle
I have many data(more than 100KB) transfer to pc,when I send the data for once...
Hello,
I am using the nrf52840 for the application, basically i want to use the timer driver in my code.
so basically if i have 5 timers of nrf52840 and i am using one...
I am using a nRF52840 Development Kit to flash a custom board with a nRF52840. When I use the nrfjprog -p (or --pinreset) option to reset the CPU, it will consume over 1mA...
I am using nRF52833 on ncs to turn on the extended broadcast. After referring to the corresponding settings, I found that the transmit power setting does not take effect....
In standard sdk 17.0.2 is it possible to know which devices did i accidently disconnect?(Interactive command s140)
for example
my central is the interactive command...
Hi, I used NRF52 DK and NRF Connect SDK 1.6. I used the st_ble_sensor sample with no changes. When I press Button 1, I expect to get a notification on the central device....
Is there a straight forward guide that demonstrates how to changes the Asset Tracker V2 application from "Active Mode" to "Passive Mode"?
Referencing the notes on the application...
Hello,
I have been working with nRF52832 microcontroller on a custom PCB. Currently, we are implementing OTA updates through BLE, and developing using the nRF toolbox app...
Hi,
I am trying to program the nRF52 DK with external j-link Base. I am using Debug IN P18 connector and connected the following pins
j-Link base nRF52 DK Debug IN P18...
