Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
As instructed to post here by We're using Zephyr on at least 4 of our products and have thousands of boards with NRF chips in the pipeline; we're trying to get the consumption...
I'm trying to install nrfutil, but for some reason the installation is unsuccessful.
After installing python and the executing pip install nrfutil, restarting both the shell...
Hello,
when my application runs, from time to time I see the following:
[00:00:29.000,000] <debug> nrf_sdh_ble: BLE event: 0x26. [00:00:29.000,000] <error> app: ERROR...
Hi Nordic team
Customer SecuX failed to use JLINK V9 to update modem firmware to Thingy91 and customer nRF91 board both.
But, JLINK V9 can program merged.hex file(application...
I want to bring up a secure bootloader with support for ECDSA and SHA-256.
I am having a hard time coming up with a combination of SDK components (frontend, backend), external...
Hi All
I'd like to implement "Fast advertising" with SDK14.10
Q1: I add some code in advertising_data_set() to do fast advertising, is that correct ?
Q2: If want...
Good afternoon. I have the Zephyr gsm_modem sample up and running for my GSM modem and a PPP connection is established to the cellular network. The example does nothing further...
After I write bonding data to flash memory (SoftDevice has been disabled before the write) I get an APP_ERROR:ERROR:FATAL. But I do not know what is causing it. I do an NRF_LOG_DEBUG...
Hi,
We added new commands for code from openthread and generated .hex file by "make -f examples/Makefile-nrf52811 NCP_SPI=1 FULL_LOGS=1 && arm-none-eabi-objcopy -O ihex...
We are planning to develop BLE and Bluetooth Mesh products using nRF52840. I have a couple of questions in use of Zephyr. 1) What is advantage of building BLE or Mesh on Zephyr...
Hi,
I tried to build the ble_app_uart example for nRF52820/s140. In my project I need to use C++ modules.
My usual approach that worked so far:
Take an example project...
Dear Nordic Semiconductor-Team and everyone else, thank you for helping the thousands of people in this forum an answering their questions thoroughly. I have a question/problem...
Hi,
I have to program the application on an nrf52840 chip that is connected to another MCU via the SPI interface. Since I have to send the image from the MCU to program...
Hi, I am building an application on the nrf5340dk using using nrf5340dk_nrf5340_cpuappns as the target board.
When I have CONFIG_NETWORKING=Y enabled in my prj.conf I am...
What causes NRF_LOG to report 'overflow' ? The buffer I provide is certainly large enough.
I have #define NRF_LOG_DEFERRED 1
What happens if I have something like this...
