hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hi, Im developing NRF52 DK. I'm building library C SPI mfrc522 for NRF52. I'm implement PCD_Read and write PCD_register look OK, But i call function PICC_IsNewCardPresent...
Hi there
I'm using a nRF5340 (DK or ADK) with the Zephyr HCI UART sample from NCS v2.9 and the SoftDevice to stream music to two headsets (1 CIG with two CIS) from our stack...
I change name by app, after get new name from my app,save it to flash, then I call gap_params_init, in this function, I reload the new name from flash and set it by sd_ble_gap_device_name_set...
Hello Nordic Community,
I’m encountering an intermittent issue with my BLE peripherals, which are based on nRF5340 + nRF7002 SoC , while testing with nRF Connect Mobile...
Hi,
We are in process of performing CE Certification on a product with the nRF9160 module mounted.
The lab wants to perform conducted testing on the module with the antenna...
hey there, i have a project which uses nrf9151 with a pressures sensor from BOSCH which uses SENT protocol to transfer data, my question is 1. Is it possible to configure...
Hello, I'm using the nrf52DK for the chip nrf52832 with nrf connect SDK v2.6.1
I want to implement an advertising timeout say 5 minutes. How can I achieve that? any example...
I'm attempting to troubleshoot a system crash when polling a sensor at higher ODRs while BLE is enabled. I'm using NCS v2.9.0 with the nRF54L15. I checked the thread stack...
I'm trying to compile the lsm6dso example for a nrf5340. I also tried the nrf52832, but I get the same error.
v2.4.2\zephyr\samples\sensor\lsm6dso
prj.conf:
CONFIG_STDOUT_CONSOLE...
Hello, i'm considering an application using nRF52840 in following configuration:
- I2S RX would be connected to some external I2S source (I2S slave)
- I2S TX would be...
Hello, I'm trying to make a application bootable through MCUBoot but I'm having a hard time generating the .bin file with MCUBoot header. According to this page I should be...
Hi I want to use nrfutil nrf5sdk-tools in MacOS but when I try to run it I get the following error.
" Error: Failed to spawn inner nrfutil-legacy executable
Caused by...
We are trying to update the SDK used by a firmware on a device that is in production. The old SDK is 2.1.0 and we are trying to update to 2.9.0.
I was able to get the firmware...
i am currently using nrf52840 dk as a hardware, nrf5sdk version 17.1.0 ,ble_app_uart peripheral example (s140 soft device )
here the maxmimum mtu is set to 247 bytes whether...
Hi everyone, When I try configure UART (parity, data_bit, stop_bit, flow_ctrl), I have noticed error when I run in terminal: "
*** Booting nRF Connect SDK v2.9.0-7787b2649840...
