According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi,
I have build the below sample for a nRF52dk-nRF52832 board.
v1.8.0\zephyr\samples\drivers\spi_fujitsu_fram
At compile time I've got this error:
I have followed...
According to Zephyr documentation it is possible to define a thread with K_FOREVER delay so it will not start till k_thread_start is called
https://developer.nordicsemi...
Hi,
i am using a PWM signal to control the brightness of a LED. When the brightness is at zero, i have a random flickering on the LED.
This signal is also present at the...
Hello, i'm using the example ble app uart and I would like to know the maximum data that I cand send to my putty and my phone. Could I have to procedure? I would like to send...
Hi,
I trouble the support team for quite a few months now with NRF5 and I am now trying to get started with the up to date SDK and hopefully being able to get along with...
I have an application using the nRF9160 and its LTE modem to connect to a LWM2M server. During some debugging I enabled LWM2M_LOG_LEVEL_DBG and saw that I consistently got...
Hi,
I recently designed a prototyping board featuring the nRF9160, which we got made for a couple of reasons.
To have multiple boards to test with
Potential to have...
hello
i want to send the data from my 5 of nRF52840DK to 1 of raspberry pi4 , i known the nRF52840dk has built-in bluetooth ble5 and raspberry pi 4 also integrate bluetooth...
I am noticing that particularly with the transmission of bytes over UART while scheduler is running, either some bytes go missing or the entire set of bytes aren't sent or...
Hello
Question: On what clock/clock-speed does the system tick timer run, when configured to use the external clock instead of the CPU clock?
I've seen a couple of...
Good afternoon,
I noticed in the nrfx driver folders there are two differente implementations for ADC: "nrfx_adc.c" and "nrfx_saadc.c"
What is the difference? Why two...
I had successfully interfaced lis3dh on nrf52 dev board using i2c protocol, i am getting raw values of x, y and z but i don't know how to interpret those values i.e. convert...
Hi,
Is there any similar to Online Power Profiler for Zigbee? How much my nRF52840 application should consume when using zboss stack? What is the minimum expected consumption...
Hi all,
I'am doing DFU via OTA
The device will be in bootloader mode ?
my current application has a thread running when i'am initiating DFU via OTA in nrf_connect app...
