Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hello,
I am currently evaluating whether the WiGLE geolocation interface is something that the nrf9160 can support.
One of the required pieces of information for that...
Hi,
I am using AFE4403 and Nrf52840, I want to assign a pin as output oscillator 4M using a nrf52 internal oscillator,
how to do that?
I am beginner , is my first...
Hi Everyone,
I'm not able to start ble scan. I've followed following example...
Developing Bluetooth Low Energy products using nRF Connect SDK
https://www.youtube.com...
Hello,
I was trying out sending RR intervals on the Heart Rate Measurement service and seeing what happens in nRF Connect. But, something is weird with the way the values...
I have a client project developed in 9160 which needs to be connected to the network via NB or LTE-M. Before each connection, I read imsi to determine the apn of the carrier...
Hi
Im trying to get the mcp2515 candriver example to work https://github.com/nrfconnect/sdk-zephyr/tree/main/samples/net/sockets/can#id3 .
i have some error during build...
We have an nRF52 with dual roles: peripheral for the connection to an app, and central, connecting to multiple third party peripheral devices.
We have come across a very...
Hello,
I'm using Segger Embedded Studio (SES) (on Windows 10) with nRfConnect SDK and nrf5340 processor.
In SES I can oben a graphical view of the configuration through...
Hi, I have developed a firmware on nRF52840 as central ble_app_uart_c\pca10056\s140. Now I have to upload it in nRF52810 which soft device should I use? Thanks!
Hi all,
I working with NCS v1.7.1 on a custom board using nRF52840 and I am trying to enable a 2-stage bootloader setup using NSIB as the first stage immutable bootloader...
Hello sir,
I am using the nrf52832 Dev board and try to send the data through custom value update then the following error occurs as ERROR 8 [NRF_ERROR_INVALID_STATE].How...
P0.25 is accessible by below:
nrf_gpio_pin_set(25);
However, when I try to access P1.00: Neither this:
nrf_gpio_pin_set(1); Nor this works:
nrf_gpio_pin_set(32);...
Hello, we have a device that uses the nRF9160 with an external GPS receiver that is controlled over I2C. I have connected the LNA enable pin to COEX0 on the nRF9160, but it...
Hi,
I was evaluating 9160DK. I tried the GPS example using 1.7.1 SDK and it works great outdoor. However, I tried to use a hackRF one to emulate the GPS signal. 9160 shows...
