I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi as I can see many other also experienced problems installing nrfutil. I spent 5 hours trying Windows 8.1, Windows 10 and a Debian Linux box. I'm no python expert and I...
Hello,
I'm working on a project related to DWM1001-DEV at University of Illinois at Urbana-Champaign to build a demo of the product that uses UWB. However, I'm having several...
Good day
Please assist, I had my power profiler (PPK II)and Bluetooth dongle both plugged into my laptop. I accidentally upgraded the firmware for power profiler (PPK II...
Hi
I am using NRF5340dk with NCS version 1.5.0, I need to port the below library which was written for nrf51.
github.com/.../ADS1231
KIndly, Help me to resolve this...
I am using SDK nRF5_SDK_15.3.0_59ac345 with nrf32832. I want to write data from central to peripheral characteristics. I wrote below code:
Everything worked fine when...
I run the program step by step, when execute NRFX_IRQ_ENABLE(SAADC_IRQn);, it will go to app_error_fault_handler,.What's wrong ? I have do nothing with it!
I am trying to set a timer pulse at 500kHz and on every high pulse i want to do a read on another pin.
I have an IC HX711, that has a 24bit output MSB. every positive...
Hi,
im a beginner and i have problems to integrate the Homekit SDK in the Connect SDK.
Maybe anyone have a link to a tutorial?
The implementation by west has no effect...
Hi, Q1) I am facing an issue with the heap memory. I am using the Cjson_Parse function which uses quit a lot of memory. So I am wondering if there is a way to increase the...
Hello,
i m working on usbd example on nRF52
i have a problem that usbd stops sending data aftew few time. the port is still enabled but the data is not sent! any proposition...
I am trying to communicate with a sensor that has some interesting timing requirements for reading information from it, it requires ~100us delays between the address to read...
I want to calculate the power consumption used by many peripheral like GPIO, TWI, UART, SPI, RTC, SAADC. I can't find these information in nrf52840 PS v1.1
Because I don...
Hi, On my Windows 10 machine I've installed nRF Connect for Desktop (v3.7.0) and then used Toolchain Manager utility for installing nRF Connect SDK (v1.6.1). Afterward, navigating...
Hi,
I'm working on a project using BLE via s140, everything was working fine until I wanted to implement usb.
I created a blank project in order to validate the usbd then...
Hello, I have and audio source and i would need to divide it beetween two frequencies (<95Hz and >=95Hz).
Im trying this thing with a nRF52840 and i was looking at DSP libraries...
