I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi, can we connect and enable the BME680 in the asset tracker code for the nRF9160DK?
It is already on the Thingy and I notice there is a switch CONFIG_BME680 in the code...
Tried to connect and Flash the hex file to enable BLE sniffing on the DK. However, the Connect desktop app was not able to detect the Development Kit.
All Steps mentioned...
Hello,
I am working on the Nordic nRF52840 development board to create a thread network and I want to use Raspberry Pi4 as thread board border router. The nordic SDK provide...
Following the insn here: https://devzone.nordicsemi.com/f/nordic-q-a/54591/nrf_serial_event_drv_err-what-is-the-cause
I found that under certain conditions, I get ERRORSRC...
Hi Nordic Community,
I have been experimenting with samples in NCS and making modifications.
Sometimes adding some code causes a hardfault during runtime. I can often...
Hello.
My application is an I2S Master that transmits audio data to an audio codec. I need to setup a transmit buffer using EasyDMA. Is EasyDMA used by default when using...
Hello,
we developed an application with a nRF52840DK as central and a custom board with a nRF52832 chip as peripheral. The peripheral sends data via NUS with a data rate...
Hi,
I'm working on the secure_bootloader example. I am having problems with micro ecc. When I compile the project, it gives an error like this.
I'm trying to follow...
The nRF5340 net-core examples (e.g., radio_test, hci_rpmsg) work fine with the 'west' build system. However, with SES, download fails with the error similar to below although...
I'm trying to narrow down the cause of a Softdevice assertion happening in S132 7.2.0 at PC=0x15810.
We set up a proprietary RF project which utilises parts of the SDK for...
Hi all,
I have a nRF52DK as peripheral and a nRF52840DK as central. I want to send data from the peripheral to the central with a data rate of 50 kBit/s.
I added a continuous...
Hi! Maybe I am missing some idea, but I wonder why Nordic prepared CSC Service for Server but there is no implementation for Client. I know there is RCSC, but I belive to...
Hey,
I try to build the bloud_client application in nRF Connected SDK v1.5.0 for Thingy:91.
I am using to build.
I am using it inside the directory
I also using before...
We are currently developing a family of products that will use Bluetooth and I am putting together the plan for the profiles for each product.
I have structured the profiles...
Is nrf5340 support only bluetooth hci_uart mode on cpunet?
I comping as following sample:
west build -p auto -b nrf5340dk_nrf5340_cpunet samples/bluetooth/hci_uart ...
